English
10
extractor cleaning. Water sense probes may become
contaminated during operation. If contamination is
present, clean water sense probes thoroughly with
damp cloth to remove any visible contamination.
Stacking Using the D
e
WALT TSTAK®
Stacking Latches (Fig. A)
WARNING:
When stacking, always place the dust
extractor on the bottom of the stack.
The DEWALT TSTAK® stacking latches
10
allow for other
TSTAK® products to securely stack one on top of the other
for convenience and portability.
To use the TSTAK® stacking latches
10
, place a TSTAK®
compatible unit on top of the dust extractor and flip up the
two TSTAK® stacking latches so that they clip securely to the
bottom of the unit.
HEPA Filter
WARNING:
The filters must always be in place
while vacuuming.
HEPA Filter Care
The HEPA filters included with this dust extractor are long
life filters. To be effective in minimizing dust recirculation,
especially in lead paint (EPA RRP Rule) applications, the
filters MUST be installed correctly and be in good condition.
Automatic Filter Cleaning System
This dust extractor has a highly effective filter cleaning
system which minimizes filter clogging. Every 20 seconds,
both filters gets automatically cleaned. The cleaning process
alternates between the filters and continues through the life
of the unit.
nOTE:
It is normal to hear a clicking sound during
this process.
nOTE:
After extended operation, the automatic filter
cleaning system may not be effective. When this happens,
the tank should be emptied and the filters may need to be
cleaned or replaced.
To Remove Filters (Fig. A, H)
1. Press the three position switch
3
to the Off (O) position
and remove the battery.
2. Release tank latches
4
and remove dust extractor
head
6
from canister. Place dust extractor head on a
level surface on its side.
3. Turn each HEPA filter
18
counterclockwise, and
carefully remove from dust extractor head, ensuring
debris does not fall into mounting hole.
nOTE
: Use care to not damage filter material.
18
Fig. H
20
27
4. Inspect filters for wear, tears or other damage.
nOTE:
If there is any doubt on the condition of the
filters, they MUST be replaced. DO NOT continue use if
filters are damaged.
WARNING:
Never use compressed air or a brush to
clean filters, otherwise damage to the filter membrane
will occur which will allow dust to pass through the
filter. If needed, rinse with room temperature water
and let air dry. Cleaning of the filters is typically
unnecessary. Even if the filter is covered with dust,
the automatic filter cleaning system will maintain
maximum performance and continue to function. If
visual damage to the filter membrane exists, replace
filters. Filters typically last between six and twelve
months, depending on use and care.
To Install Filters (Fig. A, H)
WARNING:
The filters must always be in place
while vacuuming.
1. Ensure filter seal
20
is in place and is not damaged
or dirty.
2. Line up the tabs on the HEPA filter
18
to the notches
on the dust extractor head and using moderate force,
push down and turn clockwise until the filter is secure.
nOTE:
Use care to not damage filter material.
3. Place the dust extractor head
6
onto the tank
16
and
secure it by closing the tank latches
4
.
Installing the Paper or Fleece Bag
(Fig. A, G, I)
When vacuuming fine dust, you may also use an additional
paper bag or fleece bag
12
to make emptying the
tank
16
easier.
1. Press the three position switch
3
to the Off (O) position
and remove the battery.
2. Unlatch the tank latches
4
and remove the dust
extractor head
6
from the tank
16
.
3. Attach the bag by passing the two tabs
21
on the bag
opening past the two notches
22
on the dust extractor.
4. Rotate the bag a quarter turn until the square edge
23
is facing upward.