DeWalt DWE8200PL, Руководство пользователя

Страница: 10 / 72

ENGLISH
8
Description (fig. 1)
WARNING: Never modify the power
tool or any part of it. Damage or
personal injury could result.
a. Spindle lock button
b. Spindle
c. Side handle(excluding DWE8200T)
d. Backing flange
e. Threaded clamp nut
f. Guard
g. Slider switch(DWE8 00S & DWE8 10S)
g1. Toggle switch(DWE8 00T)
INTENDED USE
The DWE8200S, DWE8200T, DWE8200PL,
DWE8210S, DWE8210PL small angle grinders
have been designed for professional grinding,
sanding, wire brushing, polishing and cutting
g
applications.
. (DWE8200PL & DWE8210PL)
g . (DWE8200PL & DWE8210PL)
DO NOT use grinding wheels other than centre
depressed wheels and flap discs.
DO NOT use under wet conditions or in the
presence of flammable liquids or gases.
These heavy-duty angle grinders are professional
power tools.
DO NOT let children come into contact with the
tool. Supervision is required when inexperienced
operators use this tool.
t 5IJTQSPEVDUJTOPUJOUFOEFEGPSVTFCZQFSTPOT
(including children) suffering from diminished
physical, sensory or mental abilities; lack of
experience, knowledge or skills unless they are
supervised by a person responsible for their
safety. Children should never be left alone with
this product.
Electrical Safety
The electric motor has been designed for one
voltage only. Always check that the power supply
corresponds to the voltage on the rating plate.
This tool is double insulated; therefore
no earth wire is required. Always check
that the power supply corresponds to
the voltage on the rating plate.
If the supply cord is damaged, it must be replaced
by a specially prepared cord available through the
D
E
WALT
service organisation.
Using an Extension Cable
If an extension cable is required, use an approved
3–core extension cable suitable for the power input
of this tool (see
Technical Data ).The minimum
conductor size is 1.5 mm 2 ; the maximum length
is 30 m.
When using a cable reel, always unwind the cable
completely.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk
of serious personal injury, turn
tool off and disconnect tool from
power source before making any
adjustments or removing/installing
attachments or accessories.
Before
reconnecting the tool, depress and
release the trigger switch to ensure that
the tool is off.
Attaching Side Handle (fig. 1)
WARNING: Before using the tool,
check that the handle is tightened
securely.
Screw the side handle (c) tightly into one of the holes
on either side of the gear case. The side handle
should always be used to maintain control of the
tool at all times.
Accessories and Attachments
It is important to choose the correct guards, backing
pads and flanges to use with grinder accessories.
Refer to chart at the end of this section for
information on choosing the correct accessories.
Note: Edge grinding and cutting can be performed
with Type 27 wheels designed and specified for this
purpose.
WARNING:
Accessories must be rated
for at least the speed recom mended
on the tool warning label. Wheels and
other accessories running over rated
accessory speed may burst and cause
injury. Threaded accessories must have
a M10 hub (for DWE8200T, DWE8200S,
DWE8200PL) or a M14 hub (for
DWE8210S, DWE8210PL).Every
unthreaded accessory must have a 22mm
arbor hole. If it doesnot, it may have been
designed for a circular saw and should not
be used.Use only the accessories shown in
chart at the end of this section.
Accessory ratings must be above listed
minimum wheel speed as shown on tool
nameplate.