ENGLISH
40
2. Turn cornering door locking lever (l)
counterclockwise one full rotation. Grasp the
corner door (m) and rotate open.
3. Place hands away from the wheel area and
position yourself so the open underside of the
shroud is facing away from you.
4. Turn the tool on and allow the tool to reach
full speed before touching the tool to the work
surface.
5. Place the wheel onto the work surface and
move the grinder from right to left to cut around
the inside corner for best dust collection.
6. Remove the tool from work surface before
turning tool off. Allow the tool to stop rotating
before laying it down.
7. Close the corner door and lock in place using
the cornering door locking lever (l).
DUST EXTRACTION (FIG. 7)
WARNING:
Use only power tools
recommended by D
E
WALT with this
attachment.
For more information about D
E
WALT power tools
compatible with this attachment, please contact one
of our authorisec services centers, listed on the back
cover, or refer to the full details of our after-sales
service available on the Internet at:
www.2helpU.com
.
WARNING:
This attachment MUST
BE used with a dust extractor system.
ALWAYS wear certified safety face or
dust mask.
NOTE:
Ensure hose connection is secure.
NOTE:
The amount of dust retained by the dust
extractor vacuum is dependent on its filter system.
Refer to the dust extractor vacuum instruction
manual for more information.
All D
E
WALT dust collection shrouds are designed to
work with the D
E
WALT Airlock DWV9000 connector.
1. Attach the DWV9000 connector (s) to your dust
collector hose (t).
2. Unlock the DWV9000 connector (s) and slide
onto dust port (h).
3. Lock the DWV9000 connector (s) to secure.
TRADITIONAL DUST EXTRACTOR VACUUM HOSES (FIG. 7)
Attach recommended dust extractor vacuum hose
to dust port (h).
Prior to Operation
• Install the guard and appropriate disc or wheel.
Do not use excessively worn discs or wheels.
• Be sure the inner and outer flanges are
mounted correctly.
• Make sure the disc or wheel rotates in the
direction of the arrows on the accessory and
the tool.
OPERATION
Instructions for Use
WARNING:
Always observe the safety
instructions and applicable regulations.
WARNING: To reduce the risk
of serious personal injury, turn
tool off and disconnect tool from
power source before making any
adjustments or removing/installing
attachments or accessories.
Before
reconnecting the tool, depress and
release the switch to ensure that the
tool is off.
WARNING:
•
Ensure all materials to be ground or
cut are secured in place.
•
Apply only a gentle pressure to the
tool. Do not exert side pressure on the
disc.
•
Avoid overloading. Should the tool
become hot, let it run a few minutes
under no-load condition.
Proper Hand Position (fi g. 8)
WARNING:
To reduce the risk of
serious personal injury,
ALWAYS
use
proper hand position as shown.
WARNING:
To reduce the risk of
serious personal injury,
ALWAYS
hold
securely in anticipation of a sudden
reaction.
Proper hand position requires one hand on the side
handle (c), with the other hand on the body of the
tool, as shown in figure 8.
Slider Switch (fi g. 1)
WARNING:
Before using the tool,
check that the side handle is tightened
securely.
CAUTION:
Before connecting the tool
to a power supply, be sure the switch is
in the off position by pressing the rear
part of the switch and releasing. Ensure
the switch is in the off position as
described above after any interruption
in power supply to the tool, such
Содержание DWE46101
Страница 1: ...DWE46101 www eu ...
Страница 2: ...1 Figure 1 Figure 2 f c p a c f o d b h i n j k l m g ...
Страница 3: ...2 Figure 5 Figure 4 Figure 3 n r q n i j k d u e l m b ...
Страница 4: ...3 Figure 8 Figure 6 Figure 7 m l m t s h u ...