ENGLISH
32
LED Worklight (fi g. 15)
The LED worklight (b) will activate when the trigger
is depressed.
Proper Hand Position (fi g. 13)
WARNING:
To reduce the risk of
serious personal injury,
ALWAYS
use
proper hand position as shown.
WARNING:
To reduce the of serious
personal injury,
ALWAYS
hold securely
in anticipation of a sudden reaction.
Proper hand position requires the tool to be held as
shown in Figure 13.
Using the Dust Extraction Adaptor
with the Sanding Platen (fi g. 17)
1. Attach the dust extraction adaptor (q). Refer to
Attaching the Dust Extraction Adaptor
.
2. Attach the sanding platen (i) as described under
Installing/Removing Accessories
.
3. Attach sanding sheet as described under
Installing/Removing Sanding Sheets
.
Using the Dust Extraction Adaptor
with Plunge Cutting Accessory
(fi g. 18)
1. Attach the dust extraction adaptor. Refer to
Attaching the Dust Extraction Adaptor
.
2. Push dust extraction arm (s) into the lower
aperture of the dust extraction adaptor (q).
3. Attach plunge cutting bit as described under
Installing/Removing Accessories
.
4. Adjust the dust extraction arm (s) for best
results.
Helpful Hints
• Always ensure the workpiece is firmly held or
clamped to prevent movement. Any movement
of the material may affect the quality of the
cutting or sanding finish.
• Do not start sanding without having the
sandpaper attached to sanding platen.
• Use coarse grit paper to sand rough surfaces,
medium grit for smooth surfaces and fine grit for
the finishing surfaces. If necessary, first make a
test run on scrap material.
• Excessive force will reduce the working
efficiency and cause motor overload. Replacing
the accessory regularly will maintain optimum
working efficiency.
• Do not allow the sandpaper to wear away, it will
damage the sanding pad.
• If the tool overheats, especially when used at
low speed, set the speed to maximum and
run it with no load for 2–3 minutes to cool
the motor. Avoid prolonged usage at very low
speeds. Always keep the blade sharp.
MAINTENANCE
Your D
E
WALT power tool has been designed to
operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
WARNING: To reduce the risk of
injury, turn unit off and disconnect
machine from power source before
installing and removing accessories,
before adjusting or changing
set-ups or when making repairs.
Be sure the trigger switch is in the OFF
position. An accidental start-up can
cause injury.
Lubrication
Your power tool requires no additional lubrication.
Cleaning
WARNING:
Blow dirt and dust out of
the main housing with dry air as often as
dirt is seen collecting in and around the
air vents. Wear approved eye protection
and approved dust mask when
performing this procedure.
WARNING:
Never use solvents or
other harsh chemicals for cleaning the
non-metallic parts of the tool. These
chemicals may weaken the materials
used in these parts. Use a cloth
dampened only with water and mild
soap. Never let any liquid get inside the
tool; never immerse any part of the tool
into a liquid.
Optional Accessories
WARNING:
Since accessories, other
than those offered by D
E
WALT, have
not been tested with this product, use
of such accessories with this tool could
Содержание DWE314
