16
en - 4
E N G L I S H
Never use a light socket.
Never connect the live (L) or neutral (N)
wires to the earth pin marked E or
.
For 115 V units with a power rating exceeding 1500 W,
we recommend to fit a plug to BS4343 standard.
Using an extension cable
If an extension cable is required, use an approved
extension cable suitable for the power input of this
tool (see technical data). The minimum conductor size
is 1.5 mm
2
. When using a cable reel, always unwind
the cable completely. Also refer to the table below.
Conductor size (mm
2
)
Cable rating (Amperes)
0.75
6
1.00
10
1.50
15
2.50
20
4.00
25
Cable length (m)
7.5
15
25
30
45
60
Voltage
Amperes
Cable rating (Amperes)
115
0 - 2.0
6
6
6
6
6
10
2.1 - 3.4
6
6
6
6
15
15
3.5 - 5.0
6
6
10
15
20
20
5.1 - 7.0
10
10
15
20
20
25
7.1 - 12.0
15
15
20
25
25
-
12.1 - 20.0
20
20
25
-
-
-
230
0 - 2.0
6
6
6
6
6
6
2.1 - 3.4
6
6
6
6
6
6
3.5 - 5.0
6
6
6
6
10
15
5.1 - 7.0
10
10
10
10
15
15
7.1 - 12.0
15
15
15
15
20
20
12.1 - 20.0
20
20
20
20
25
-
Your D
E
WALT Dry Diamond Drilling
machine has been designed for drilling
into masonry materials such as brick
breezeblock, etc. For drilling concrete,
a wet drilling rig must be used.
Assembly and adjustment
Prior to assembly and adjustment always
unplug the tool.
Inserting and removing a bit (fig. A)
Keyed chuck (6)
• Open the chuck by turning the sleeve (7)
counterclockwise and insert the bit shank.
• Put the chuck key (8) into each hole in the side
of the chuck and turn clockwise until tight.
Keyless chuck (5)
• Open the chuck by turning the sleeve
counterclockwise and insert the bit shank.
• Tighten firmly by turning the sleeve clockwise.
• To remove the bit, proceed in reverse order.
Fitting the side handle (fig. A)
The side handle (3) can be fitted to suit both
RH- and LH-users.
Always use the Drill with the side handle
properly assembled.
• Loosen the side handle.
• For RH-users, slide the side handle clamp over the
43 mm collar behind the chuck, handle at the left.
• For LH-users, slide the side handle clamp over the
43 mm collar behind the chuck, handle at the right.
• Rotate the side handle to the desired position
and tighten the handle.
Setting the drilling depth (fig. B)
• Insert the required drill bit into the chuck.
• Slacken the side handle (3).
• Fit the depth adjustment rod (4) through the hole
in the side handle clamp.
• Adjust the drilling depth as shown.
• Tighten the side handle.
Содержание DW516K
