background image

6

English

Important Safety Instructions for All 
Battery Packs

When ordering replacement battery packs, be sure to include the 
catalog number and voltage. Consult the chart at the end of this 
manual for compatibility of chargers and battery packs.
The battery pack is not fully charged out of the carton. Before using 
the battery pack and charger, read the safety instructions below and 
then follow charging procedures outlined.

READ ALL INSTRUCTIONS

• 

Do not charge or use the battery pack in explosive 
atmospheres, such as in the presence of flammable liquids, 
gases or dust.

 Inserting or removing the battery pack from the 

charger may ignite the dust or fumes.

•  NEVER force the battery pack into the charger. DO NOT 

modify the battery pack in any way to fit into a non-
compatible charger as battery pack may rupture causing 
serious personal injury. 

Consult the chart at the end of this 

manual for compatibility of batteries and chargers. 

•  Charge the battery packs only in designated D

E

WALT chargers.

• 

DO NOT

 splash or immerse in water or other liquids.

•  Do not store or use the tool and battery pack in locations 

where the temperature may reach or exceed 105 °F (40 °C) 
(such as outside sheds or metal buildings in summer).

 For 

best life store battery packs in a cool, dry location. 

  NOTE: Do not store the battery packs in a tool with the 

trigger switch locked on. Never tape the trigger switch in the 
ON position.

WARNING:

 Fire hazard. Never attempt to open the battery pack 

for any reason. If the battery pack case is cracked or damaged, do 
not insert into the charger. Do not crush, drop or damage the battery 
pack. Do not use a battery pack or charger that has received a sharp 

blow, been dropped, run over or damaged in any way (e.g., pierced 
with a nail, hit with a hammer, stepped on). Damaged battery packs 
should be returned to the service center for recycling.

WARNING: Fire hazard. Do not store or carry the battery 

pack so that metal objects can contact exposed battery 
terminals.

 For example, do not place the battery pack in aprons, 

pockets, tool boxes, product kit boxes, drawers, etc., with loose 
nails, screws, keys, etc. 

Transporting batteries can possibly 

cause fires if the battery terminals inadvertently come in 
contact with conductive materials such as keys, coins, hand 
tools and the like.

 The US Department of Transportation Hazardous 

Material Regulations (HMR) actually prohibit transporting batteries in 
commerce or on airplanes (e.g., packed in suitcases and carry-on 
luggage) UNLESS they are properly protected from short circuits. 
So when transporting individual battery packs, make sure that the 
battery terminals are protected and well insulated from materials that 
could contact them and cause a short circuit.

SPECIFIC SAFETY INSTRUCTIONS FOR LITHIUM ION (Li-Ion)

• 

Do not incinerate the battery pack even if it is severely 
damaged or is completely worn out.

 The battery pack can 

explode in a fire. Toxic fumes and materials are created when 
lithium ion battery packs are burned.

• 

If battery contents come into contact with the skin, 
immediately wash area with mild soap and water. 

If battery 

liquid gets into the eye, rinse water over the open eye for 15 
minutes or until irritation ceases. If medical attention is needed, 
the battery electrolyte is composed of a mixture of liquid organic 
carbonates and lithium salts.

• 

Contents of opened battery cells may cause respiratory 
irritation.

 Provide fresh air. If symptoms persist, seek medical 

attention.

WARNING: 

Burn hazard. Battery liquid may be flammable if 

exposed to spark or flame. 

Содержание DCS373P2



















Отзывы: