DeWalt DCF6202, Оригинальное руководство пользователя

Страница: 14 / 60

12
EngLIsh
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories.
An accidental
start-up can cause injury.
Description (Fig. A)
WARNING: Never modify the power tool or any part of it.
Damage or personal injury could result.
1
Screw guide
2 Screw length adjustment
3
Fine depth adjustment knob
4 Fine depth adjustment indicator
5
Advancing mechanism
6 Collated housing
7
Shoe
8 Release buttons
9
Collated screwdriver bit
Intended Use
This collated drywall magazine is a professional attachment
designed to be used with the DCF620
D
e
WALT screwdriver for
professional driving of collated screws.
DO nOT
use under wet conditions or in the presence of
flammable liquids or gases.
DO nOT
let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
•
Young children and the infirm. This appliance is not
intended for use by young children or infirm persons
without supervision.
• This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with this product.
Setting Magazine Screw Length (Fig. C)
This magazine is designed for 25–57 mm screw lengths. Failure
to set the correct screw length can cause screws to not be
driven accurately which can result in the failure to advance to
the next screw or screws not being driven properly. The shoe
has marked specific slots for each of the most common screws,
however this attachment can still drive any size screw between
25–57 mm. To accommodate for less common screws adjust to
the next longest slot.
CAUTION: Do not adjust while a screw strip is in
the magazine.
1. Slide screw length adjustment tab 2 to the left.
2. Holding the screw length adjustment tab in place, adjust
the shoe 7 to the desired length.
3. Release the screw length adjustment tab. Make sure that the
locking pin has fully returned and is in the correct position.
OPERATION
Instructions for Use
WARNING: Always observe the safety instructions and
applicable regulations.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories.
An accidental
start-up can cause injury.
Date Code Position (Fig. A)
The date code 10 , which also includes the year of manufacture,
is printed into the housing.
Example:
2019 XX XX
Year of Manufacture
Fitting the Collated Screwdriver Bit (Fig. A, B)
NOTICE: For proper operation only use a D
e
WALT collated
screwdriver bit.
1. Remove the nose cone from the screwdriver.
2. Remove the mounted bit and bit holder from
the screwdriver.
nOTE: Refer to and follow all instructions on changing bits
and holders in your screwdriver manual.
3. Insert the provided collated screwdriving bit 9 into the bit
holder until it clicks into place.
Installing and Removing the Magazine from
the Screwdriver (Fig. B)
With the the nose cone removed and provided driver bit 9
installed, push the magazine over the bit onto the screwdriver
until the magazine clicks into place and ensure that it does
not disengage.
nOTE: If necessary, rotate the attachment to locate properly
on mount.
nOTE: Make sure the screwdriver control lever is set to forward
rotation before use.
To remove the magazine, press and hold the release buttons
8
on both sides of the accessory and pull accessory off
the screwdriver.
Markings on Tool
The following pictograms are shown on the tool:
Read instruction manual before use.
Wear ear protection.
Wear eye protection.