DeWalt D28409, Инструкция по эксплуатации

Страница: 6 / 7

E N G L I S H
Your risk from these exposures varies, depending on how
often you do this type of work. To reduce your exposure
to these chemicals: work in a well ventilated area, and
work with approved safety equipment, such as those dust
masks that are specially designed to filter out microscopic
particles.
Avoid prolonged contact with dust from power
sanding, sawing, grinding, drilling, and other
construction activities. Wear protective clothing and
wash exposed areas with soap and water. Allowing
dust to get into your mouth, eyes, or lay on the skin
may promote absorption of harmful chemicals.
WARNING: Use of this tool can generate
and/or disburse dust, which may cause
serious and permanent respiratory or other
injury. Always use approved respiratory
protection appropriate for the dust exposure.
Direct particles away from face and body.
The label on your tool may include the following
symbols. The symbols and their definitions are as
follows:
V volts
A amperes
Hz hertz
W watts
min minutes
alternating current
direct current
n
0
no load speed
earthing terminal
safety alert symbol
Class II Construction (double insulated)
…/min revolutions or reciprocation per minute
BPM beats per minute
Save these instructions
DESCRIPTION
Sidle handle
Spindle lock
Lock-on button
Trigger switch
Clamp washer
Spindle
Backing pad
Sanding paper
A
B
C
D
E
F
G
H
FEATURES
Side Handle
An side handle is furnished with your tool and can be
installed on either side of the front housing. This handle
should be used at all times to maintain complete control of
the tool.
release the trigger switch once. Do not unplug the tool with
the switch in the locked on condition. Make sure the tool is
not locked on when plugging in. A locked on tool will start
immediately when plugged in.
6
..........
..........
..........
..........
..........
..........
..........
..........
..........
..........
..........
..........
..........
•
•
Spindle Lock Button (Fig. 1)
WARNING: To reduce the risk of
serious personal injury, turn tool off and
disconnect tool from power source before
making any adjustments or removing/
installing attachments or accessories.
In order to prevent the spindle of the tool from rotating
while installing or removing accessories, a spindle lock
button has been provided in the gear head of the machine.
To lock the spindle, depress and hold the lock button.
NEVER DEPRESS THE SPINDLE LOCK BUTTON WITH
THE TOOL RUNNING OR COASTING.
The tool can be locked on for continuous use by squeezing
the trigger switch fully and depressing the lock button
shown in Figure 2. Hold the lock button in as you gently
release the trigger switch. The tool will continue to run. To
turn the tool off from a locked on position, squeeze and
OPERATION
WARNING: To reduce the risk of
serious personal injury, turn tool off and
disconnect tool from power source before
making any adjustments or removing/
installing attachments or accessories.
Sanding Application
ATTACHING AND REMOVING BACKING PAD
OR SANDING PAPER
(Figures 4, 5, and 6)
To attach the sanding paper, push the hub of the clamp
washer through the center of the backing pad and sanding
paper, as far as it will go, and also through the backing
pad. Engage the clamp washer threads on the tool spindle
and thread assembly clockwise, completely down on the
spindle. Hold the spindle from rotating by engaging the
spindle lock button.
To remove the backing pad and sanding, use a cloth or
glove to protect your hand. Turn the clamp washer assembly
counterclockwise (Figure 6). Hold the spindle from rotating
by engaging the spindle lock button.
Sanding
(See Figure 7) When using an abrasive disc, hold the tool
so that an angle of 10˚ to 15˚ exists between the disc and
the work. If only the outer edge of the sanding disc is used,
a rough cut will result. If the sanding disc is pressed flat
against the work, the sanding action will be irregular and
bumpy, and the tool will be difficult to control.
MAINTENANCE
WARNING: To reduce the risk of
serious personal injury, turn tool off and
disconnect tool from power source before
making any adjustments or removing/
installing attachments or accessories.