DeWalt D28400, Руководство пользователя

Страница: 23 / 88

23
E N G L I S H
2.50 20
4.00 25
Cable length (m)
7.5 15 25 30 45 60
Voltage Amperes Cable rating (Amperes)
115 0 - 2.0 6 6 6 6 6 10
2.1 - 3.4 6 6 6 6 15 15
3.5 - 5.0 6 6 10 15 20 20
5.1 - 7.0 10 10 15 20 20 25
7.1 - 12.0 15 15 20 25 25 -
12.1 - 20.0 20 20 25 - - -
230 0 - 2.0 6 6 6 6 6 6
2.1 - 3.4 6 6 6 6 6 6
3.5 - 5.0 6 6 6 6 10 15
5.1 - 7.0 10 10 10 10 15 15
7.1 - 12.0 15 15 15 15 20 20
12.1 - 20.0 20 20 20 20 25 -
Assembly and adjustment
Prior to assembly and adjustment always
unplug the tool.
Mounting and removing the guard (fig. B)
• Place the angle grinder on a table, spindle up.
• Release the clamping lock (6) and hold the guard
(4) over the tool as shown.
• Align the lugs (7) with the notches (8).
• Press the guard down and rotate it to the
required posiiton.
• If required, increase the clamping force by
tightening the screw (9).
• Tighten the clamping lock.
• To remove the guard, release the clamping lock.
Never use the tool without the guard in
place.
Fitting and removing a grinding or cutting disc
(fig. C1 - C3)
• Place the tool on a table, guard up.
• Fit the inner flange (10) correctly onto the spindle
(11) (fig. C1).
• Place the disc (12) on the flange (10) (fig. C2).
When fitting a disc with a raised center, make
sure that the raised centre (13) is facing the
flange (10).
• Screw the outer flange (14) onto the spindle (11)
(fig. C3):
- the ring on the flange (14) must face towards
the disc when fitting a grinding disc (A);
- the ring on the flange (14) must face away from
the disc when fitting a cutting disc (B).
• Press the spindle lock (3) and rotate the spindle
(11) until it locks in position (fig. C2)
• Tighten the flange (14) with the two-pin spanner
supplied.
• Release the spindle lock.
• To remove the disc, loosen the flange (14) with
the two-pin spanner.
Do not use a damaged disc.
Fitting a wire cup brush
• Screw the wire cup brush directly onto the
spindle without the use of the spacer and
threaded flange.
Mounting the side handle (fig. D1 & D2)
• For grinding, screw the side handle (5) tightly into
one of the holes (15) on either side of the gear
case (fig. D1).
• For cutting, screw the side handle (5) tightly into
the top hole (16) or into one of the holes (17) on
either side of the gear case (fig. D2).
Instructions for use
• Always observe the safety instructions
and applicable regulations.
• Ensure all materials to be ground or cut
are secured in place.
• Apply only a gentle pressure to the tool.
Do not exert side pressure on the disc.
• Avoid overloading. Should the tool
become hot, let it run a few minutes
under no load condition.
Prior to operation:
• Install the guard and appropriate disc or wheel.
Do not use excessively worn discs or wheels.
• Be sure the inner and outer flange are mounted
correctly.
• Make sure the disc or wheel rotates in the direction
of the arrows on the accessory and the tool.