background image

13

  2. Apply minimum pressure to work surface, allowing the tool to operate at high 

speed. Material removal rate is greatest when the tool operates at high speed.

  3. Maintain a 5

˚

 to 10

˚

 angle between the tool         

5

˚

-10

˚

and work surface for wire cup brushes.

  4. Maintain contact between the edge of the wheel 

and the work surface with wire wheels. 

  5. Continuous move the tool in a forward and back 

motion to avoid creating gouges in the work 

surface. Allowing the tool to rest on the work surface    

 

without moving, or moving the tool in a circular motion 

causes burning and swirling marks on the work 

surface. 

  6. Remove the tool from the work surface before turning 

the tool off. Allow the tool to stop rotating before setting 

it down.

CAUTION: 

Use extra care when working over an edge, as a sudden sharp 

movement of grinder may be experienced. 

Mounting and Using Cutting (Type 1) Wheels 

Cutting wheels include diamond wheels and abrasive discs. Abrasive cutting wheels 

for metal and concrete use are available. Diamond blades for concrete cutting can 

also be used.

NOTE:

 All grinders that use Type 1 wheels use the quick change wheel release (G).

WARNING: 

A closed, 2-sided cutting wheel guard is not included with this tool 

and is re quired when using cutting wheels. Fail ure to use proper flange and guard 

can re sult in injury resulting from wheel breakage and wheel contact. See page 8 for 

more information.

MOUNTING CLOSED (TYPE 1) GUARD 

  

J

L

K

WARNING: To reduce the risk of serious 

personal injury, turn tool off and disconnect 

tool from power source before making any 

adjustments or removing/installing 

attachments or accessories. 

  1.  Open the guard latch (J). Align the lugs (K) 

on the guard with the slots (L) on the gear 

case.   

  3. Maintain a 5

˚

 to 15

˚

 angle between the tool      

5

˚

-15

˚

 

and work surface. The san ding disc should 

contact approximately one inch of work surface.

  4. Move the tool constantly in a straight line to 

prevent burning and swirling of work surface. 

Allowing the tool to rest on the work surface 

without moving, or moving the tool in a circular 

motion causes burning and swirling marks on the work surface. 

  5. Remove the tool from work surface before turning tool off. Allow the tool to stop 

rotating before laying it down. 

Mounting and Using Wire Brushes 

and Wire Wheels

Wire cup brushes or wire wheels screw directly on the grinder spindle without the 

use of flanges. Use only wire brushes or wheels provided with a 14m2 threaded hub. 

A Type 27 guard is required when using wire brushes and wheels.

CAUTION: Wear work gloves when handling wire brushes and wheels.

 They 

can become sharp.

CAUTION: 

Wheel or brush must not touch guard when mounted or while in use. 

Undetectable damage could occur to the accessory, causing wires to fragment from 

accessory wheel or cup.

MOUNTING WIRE BRUSHES AND WIRE WHEELS

WARNING: To reduce the risk of serious personal injury, turn tool off and 

disconnect tool from power source before making any adjustments or removing/

installing attachments or accessories.

  1. Thread the wheel on the spindle by hand.
  2. Depress spindle lock button and use a wrench on the hub of the wire wheel or 

brush to tighten the wheel.

  3. To remove the wheel, reverse the above procedure.

CAUTION:

 Failure to properly seat the wheel hub before turning the tool on may 

result in damage to tool or wheel.

USING WIRE CUP BRUSHES AND WIRE WHEELS

Wire wheels and brushes can be used for removing rust, scale and paint, and for 

smoothing irregular surfaces.
  1. Allow the tool to reach full speed before touching the tool to the work surface. 

Содержание D28065-XE





















Отзывы: