22
E N G L I S H
• Check for damage to the tool, parts or accessories
which may have occurred during transport.
• Take the time to thoroughly read and understand
this manual prior to operation.
Description (fig. A)
Your sliding table D271055 has been designed to
extend the versatility of your D
E
WALT flip-over saw
in saw bench mode. This attachment fits to the
left-hand side of the machine and is used for straight
and mitre crosscuts. In order to gain maximum
capacities, the sliding table support rail can be
positioned either in the rear position or in the forward
position, or anywhere in between.
1 Sliding table support rail
2 Sliding table
3 Mitre quadrant
4 Fence
5 Mitre scale
6 Fence setting guide
Assembly
Do not mount this attachment to any
other machine than the D
E
WALT D27105
in saw bench mode. Also refer to the
instruction manual of your flip-over saw.
The mounting brackets (fig. B)
• Place the rear mounting bracket (7) onto the strip
(8) and secure it with the socket head bolt (9) and
nut (10).
• Mount the front mounting bracket in the same way.
The securing/adjusting hook (fig. C2 - C3)
• Insert the bushing (11) into the hole (12) in the
frame (fig. C1).
• Place the lock bracket (13) onto the frame
around the bushing.
• Pass the bolt (14) through the bracket and the
bushing into the threaded hole on the opposite
side of the bushing.
• Tighten the bolt to secure the bracket.
• Slacken the bolts (16) and (17) and slide the
securing/adjusting hook (15) to the middle of the
sliding table support rail (1) (fig. C2).
• Tighten the bolts temporarily.
• Press the hinge rail (18) of the sliding table into
the mounting brackets (7) (fig. C3).
• Swivel the support rail (1) to horizontal position
making sure that the fork (19) slides over the lock
bracket (13) (fig. C4). Adjust the position of the
securing/adjusting hook and the lock bracket as
necessary.
• Rotate the securing hook (20) onto the lock
bracket (13) and turn on the star grip (21) (fig. C5).
• Adjust the star grip (22) (fig. C3).
The sliding table (fig. D)
• Carefully engage the bearings (23) onto the right-
hand support rail and swivel the sliding table to
horizontal position to engage the other bearings
on the left-hand support rail.
The fence (fig. E)
• Insert the 90° guide piece (24) into the fence (4),
engaging it into the groove of the sliding table (2).
• Engage the fence (4) into the mitre quadrant (3)
up to 1 cm before the blade and tighten the
wingnut (25).
• Introduce the measuring tape (26) into the top of
the fence.
• Cut off any excess tape at 1 cm.
• Slide on the fence setting guide (6) and lock the
star knob (27) temporarily.
• Slide on the material support (28) and lock the
star knob (29) temporarily.
• Slide on the squares (30) and lock their star
knobs temporarily.
Adjustment
Checking and adjusting the table tops (fig. F1 & F2)
The following procedure assumes that the side
panels of the mitre saw are parallel to each other.
If the side panels need readjustment due to mobile
usage, proceed as follows:
• Fold the legs of the mitre saw.
• Loosen the side panel screws.
• Place the mitre saw on a flat surface.
• Tighten the side panel screws.
• Slide the fence (4) over the table top of your
sawing machine to the rear.
• If adjustment is required, proceed as follows:
Содержание D271055
