background image

6

CAUTION: 

When reversing to clear jammed bits, be ready for strong reactive torque. 

To reverse the rotary hammer, turn it off and align the reversing lever (H) with the 

yellow arrow pointing backward (viewed when holding drill in operating position). 
To position the lever for forward operation, turn the rotary hammer off and align the 

reversing lever (H) with the yellow arrow pointing forward (viewed when holding drill 

in operating position). 

FIG. 2

DRILL-ONLY MODE

MODE PERÇAGE SEULEMENT

MODO SÓLO TALADRO

F

G

HAMMERDRILL MODE

MODE PERFORATION-PERÇAGE

MODO TALADRO/PERCUTOR

F

G

HAMMER-ONLY MODE

MODE PERFORATION SEULEMENT

MODO SÓLO MARTILLO

G

F

Mode Selector (Fig. 2)

N

OTICE: 

Tool must come to a complete stop before activating the mode selector 

button or damage to the tool may result.

DRILL-ONLY MODE 

To use drill-only mode, press mode selector button (F) and turn the mode selector 

(G) so the yellow arrow points to the corresponding symbol as shown. Use drill-only 

mode for wood, metal, and plastics.

HAMMERDRILL MODE 

To use hammerdrill mode, press the mode selector button (F) and turn the mode 

selector (G) so the yellow arrow points to the corresponding symbol as shown. Use 

this mode for masonry drilling.

HAMMER-ONLY MODE 

For light chiseling, press the mode selector button (F) and turn the mode selector (G) 

so the yellow arrow points to the corresponding symbol as shown. 

NOTE: 

The yellow arrow on the mode selector 

MUST

 be aligned with one of the 

symbols at all times. There are no operable positions between the positions.

SDS Plus

®

 Chuck (Fig. 1)

WARNING: To reduce the risk of serious personal injury, turn tool off and 

disconnect tool from power source before making any adjustments or removing/

installing attachments or accessories.

WARNING: 

Burn Hazard. ALWAYS wear gloves when changing bits. Accessible 

metal parts on the tool and bits may get extremely hot during operation. Small bits of 

broken material may damage bare hands.

WARNING: 

Do not attempt to tighten or loosen drill bits (or any other accessory) 

by gripping the front part of the chuck and turning the tool on. Damage to the chuck 

and personal injury may occur.
To insert bit, insert shank of bit about 19 mm (3/4"), no further than 22 mm (7/8") 

into chuck. Push and rotate bit until it locks in place. The bit will be securely held.
To release bit, pull the chuck sleeve (E) back and remove the bit.

OPERATION

WARNING: To reduce the risk of serious personal injury, turn tool off and 

disconnect tool from power source before making any adjustments or removing/

installing attachments or accessories.

Содержание D25012-XE













Отзывы: