DeWalt D24000, Инструкция по эксплуатации

Страница: 36 / 124

36
E N G L I S H
Safety instructions
When using stationary power tools, always observe the safety
regulations applicable in your country to reduce the risk of fire,
electric shock and personal injury.
Read all of this manual carefully before operating the tool.
Save this manual for future reference.
General
1 Keep work area clean
Cluttered areas and benches can cause accidents.
2 Consider work area environment
Do not expose the tool to rain. Do not use the tool in damp or wet
conditions. Keep the work area well lit (250-300 Lux). Do not use the
tool where there is a risk of causing fire or explosion, e.g. in the
presence of flammable liquids and gases.
3 Keep children away
Do not allow children, visitors or animals to come near the work area or
to touch the tool or the mains cable.
4 Dress properly
Do not wear loose clothing or jewellery, as these can be caught in
moving parts. Wear protective hair covering to keep long hair out of the
way. Preferably wear suitable gloves and non-slip footwear.
5 Personal protection
Always use safety glasses. Use a face or dust mask whenever the
operations may produce dust or flying particles. If these particles might
be considerably hot, also wear a heat-resistant apron. Wear ear
protection at all times. Wear a safety helmet at all times.
6 Guard against electric shock
Prevent body contact with earthed or grounded surfaces (e.g. pipes,
radiators, cookers and refrigerators). Avoid touching the plugged-in mains
cable when it is wet. Do not stand in pools when operating the tool.
7 Do not overreach
Keep proper footing and balance at all times.
8 Stay alert
Watch what you are doing. Use common sense.
Do not operate the tool when you are tired.
9 Secure workpiece
Use clamps or a vice to hold the workpiece. It is safer and it frees both
hands to operate the tool.
10 Connect dust extraction equipment
If devices are provided for the connection of dust extraction and
collection facilities, ensure that these are connected and properly used.
11 Remove adjusting keys and wrenches
Always check that adjusting keys and wrenches are removed from the
tool before operating the tool.
12 Extension cables
Before use, inspect the extension cable and replace if damaged.
When using the tool outdoors, only use extension cables intended for
outdoor use and marked accordingly.
13 Use appropriate tool
The intended use is described in this instruction manual. Do not force
small tools or attachments to do the job of a heavy-duty tool. The tool
will do the job better and safer at the rate for which it was intended.
Do not force the tool.
Warning! The use of any accessory or attachment or performance of
any operation with this tool other than those recommended in this
instruction manual may present a risk of personal injury.
14 Check for damaged parts
Before use, carefully check the tool and mains cable for damage.
Check for misalignment and seizure of moving parts, breakage of
parts, damage to guards and switches and any other conditions that
may affect its operation. Ensure that the tool will operate properly and
perform its intended function. Do not use the tool if any part is damaged
or defective. Do not use the tool if the switch does not turn it on and off.
Have any damaged or defective parts replaced by an authorised
D
E
WALT repair agent. Never attempt any repairs yourself.
15 Unplug tool
Switch off and wait for the tool to come to a complete standstill before
leaving it unattended. Unplug the tool when not in use, before changing
any parts of the tools, accessories or attachments and before servicing.
16 Avoid unintentional starting
Be sure that the tool is switched off before plugging in.
17 Do not abuse cord
Never pull the cord to disconnect from the socket. Keep the cord away
from heat, oil and sharp edges.
18 Store idle tools
When not in use, tools must be stored in a dry place and locked up
securely, out of reach of children.
19 Maintain tools with care
Keep the tools in good condition and clean for better and safer
performance. Follow the instructions for maintenance and changing
accessories. Keep all handles and switches dry, clean and free from oil
and grease.
20 Repairs
This tool is in accordance with the relevant safety regulations. Have
your tool repaired by an authorised D
E
WALT repair agent. Repairs
should only be carried out by qualified persons using original spare
parts; otherwise this may result in considerable danger to the user.
Additional safety rules for tile saws
• Do not use the machine if it is not fully assembled. Do not operate the
machine as a hand-held power tool.
• Make sure all locking knobs and clamp handles are tight before starting
any operation.
• Never place either hand in the cutting disc area when the machine is
connected to the electrical power source.
•
Never cut workpieces that require manual action closer than 15 cm
from the rotating cutting disc.
• Never reach in the back of the cutting disc.
• Do not perform any operation freehand. Hold the workpiece firmly
against the fence and the guide.
• Switch off the machine and wait for the cutting disc to stop before
moving the workpiece or changing the settings.
• Never attempt to stop a machine in motion rapidly by jamming a tool or
other means against the cutting disc; serious accidents can be caused
unintentionally in this way.
• Keep the surrounding area of the machine well maintained and free of
loose materials, e.g. debris and cut-offs.
• Check periodically that the motor air slots are clean and free of dust.
• Disconnect the machine from the mains before carrying out any
maintenance work or when changing the cutting disc.
• Never perform any cleaning or maintenance work when the machine is
still running and the head is not in the rest position.
• Select the correct cutting disc for the material to be cut.
• Use only the cutting discs specified in this manual. Never use grinding
discs. Never use circular saw blades or any other types of toothed
blades.
• The max. allowable speed of the cutting disc, or any other suitable
accessory, must always be equal to or greater than the no-load speed
of the machine specified on the nameplate.
• Do not use cutting discs that do not conform to the dimensions stated
in the technical data. Do not use any spacers to make a disc fit onto
the spindle.
• Inspect cutting discs before each use. Do not use chipped, cracked or
otherwise defective discs.
• Ensure that the cutting disc is mounted correctly before use.
• Let the machine run at no-load in a safe position for at least 30 seconds.
If there is a considerable vibration or if any other defect occurs,
stop the machine and check it to determine the cause.