Page 6
SB-2-179-F
TROUBLESHOOTING (Continued)
CONDITION
CAUSE
CORRECTION
Fluid dripping or leaking from
bottom of cup
Runs and sags
Thin, sandy coarse finish drying
before it flows out
Thick, dimpled finish "orange
peel"
Cup loose on gun.
Washer worn or missing below cup.
Cup threads dirty.
Too much material flow.
Material too thin.
Gun tilted on an angle, or gun motion too
slow.
Gun too far from surface.
Too much air pressure.
Improper thinner being used.
Gun too close to surface.
Air pressure too low.
Improper thinner being used.
Material not properly mixed.
Surface rough, oily, dirty.
Tighten.
Replace washer.
Clean.
Adjust gun or reduce fluid flow.
Mix properly or apply light coats.
Hold gun at right angle to work and adapt to
proper gun technique.
Check distance. Normally approx. 8".
Reduce air pressure and check spray pattern.
Follow paint manufacturer's mixing instrs.
Check distance. Normally approx. 8".
Too much material coarsely atomized.
Increase air pressure or reduce fluid flow.
Follow paint manufacturer's mixing instrs.
Follow paint manufacturer's mixing instrs.
Properly clean and prepare.
42884-214-K5 3/8"
42884-215-K10 5/8"
Cleaning Brushes
These brushes are
helpful in cleaning
threads and
recesses of gun
body.
GFG-413-2 Air
Adjustment Valve
Installs into gun
to enable user to
control and
reduce air
pressure at the
gun. Replaces
6000-12 plug.
HARG-510
Air Regulator
Use to maintain
nearly constant out-
let pressure despite
changes in inlet
pressure and down-
stream flow.
WR-103 Wrench
Contains all neces-
sary tip, hose, and
nut sizes used on or
with gun.
HAV-500 OR
HAV-501
Adjusting Valve
(HAV-501 SHOWN)
HAV-500 does not
have pressure gage.
Use to control air
pessure at gun.
Spray Gun Lube
SSL-10-K12
(2 oz. bottle)
Compatible with all
paint materials; con-
tains no silicone or
petroleum distil-
lates to contaminate
paint.
GH-407 Gun Holder
(1) Wall mount
bracket included
with GH-407.
GH-505 Gun Holder
Gun holders are
made to hold stan-
dard paint cups,
gravity feed guns
and cups, and paint
filters.
GFC-501 (Acetal) 20 Oz. Cup
GFC-502 (Aluminum) 32 Oz. Cup
Gravity Feed Cups
Joins any single piece Devilbiss air cap
with latest version MBC-368 or MSA-1
retaining ring,. Helps prevent parts loss
and provides easier assembly.
JGA-156-K10 Spring Clips
These gravity feed cups are designed
to be used with GFG gravity feed spray
guns.
ACCESSORIES
Spray Gun and Cup Kits
GFG-517 Spray Gun is also sold in the follow-
ing Kits:
Each Kits includes (1) GFG-517
Spray Gun and (1) GFG-502 Cup:
GFG-618-80FW GFG-618-90FF
GFG-618-90FW
OMX-70-K48 PAINT CUP LINER KIT
Allows quick and easy clean-up.
Consists of :
1 - Piercing Tool,
48 - Disposable Liners,
48 - Drain Bushings
HAF-507 Whirlwind™
In-Line Air Filter
Removes water, oil, and
debris from the air line.
Quick Disconnect Approved For
HVLP Guns (Air)
High Flow Ball and Ring Type.
HC-4700
1/4" NPT(F)
HC-4699
1/4" NPT(M)
HC-4419
1/4" NPS(F)
HC-1166
1/4" NPT(M)
6/04 ©2004
Inc. All rights reserved. Printed in U.S.A.
WARRANTY
This product is covered by DeVilbiss' 1 Year Limited Warranty.
DeVilbiss Worldwide Sales and Service Listing:
www.devilbiss.com
Industrial Finishing
DeVilbiss has authorized distributors throughout the world. For
technical assistance or the distributor nearest you, see listing below.
U.S./Canada Technical Service Office:
195 Internationale Blvd., Glendale Heights, IL 60139
Toll-Free Telephone: 1-888-992-4657 (U.S.A. and Canada only)
Toll-Free Fax: 1-800-368-8401
Scrubs® are a pre-moistened
hand cleaner towel for painters.
No water is needed.
29-3100 Scrubs
®
Hand
Cleaner Towels
