background image

8 - ENG

D22228

Break-in  Procedures

INSTALLATION  AND  BREAK-IN

PROCEDURES

GROUNDING  INSTRUCTIONS

Additional  Regulators  and

Controls

Since the air tank pressure is usually greater than that

which is needed, a regulator is employed to control the

air pressure ahead of any individual air driven device.

Separate air transformers which combine the function of

air regulation, moisture and dirt removal should be used

where applicable.

This procedure is required:

1. Before the air compressor is put into service.

2. When the check valve is replaced.

a. Set the pressure switch lever to the "OFF"

position.

b. Plug the power cord into the correct branch

circuit receptacle.

c. Turn the regulator clockwise, opening it fully, to

prevent air pressure build-up in the tank.

d. Move the pressure switch lever to "ON/AUTO".

The compressor will start.

e. Run the compressor for 15 minutes. Make sure

the regulator is open and there is no tank

pressure build-up.

f. After 15 minutes, close the regulator by turning

knob counterclockwise. The air receiver will fill

to cut-out pressure and the motor will stop. The

compressor is now ready for use.

Serious damage may result if the

following break-in instructions are

not closely followed.

The air compressor is equipped with a cord having a

grounded wire with an appropriate grounding plug. The

plug must be used with an outlet that has been installed

and grounded in accordance with all local codes and

ordinances. The outlet must have the same configuration

as the plug. See illustration. 

DO NOT USE AN ADAPT-

ER.

Inspect the plug and cord before each use. Do not use if

there are signs of damage.

Do not modify the plug that has been provided. If it does

not fit the available outlet, the correct outlet should be

installed by a qualified electrician.

If repairing or replacing cord or plug, the grounding wire

must be kept separate from the current-carrying wires.

Never connect the grounding wire to a flat blade plug

terminal. The grounding wire has insulation with an outer

surface that is green - with or without yellow stripes.

If these grounding instructions are not completely under-

stood, or if in doubt as to whether the compressor is

properly grounded, have the installation checked by a

qualified electrician.

IMPROPER GROUNDING CAN RESULT IN

ELECTRICAL SHOCK.

RISK OF ELECTRICAL SHOCK!  IN THE EVENT

OF A SHORT CIRCUIT, GROUNDING REDUCES

THE RISK OF SHOCK BY PROVIDING AN

ESCAPE WIRE FOR THE ELECTRIC CURRENT.

THIS AIR COMPRESSOR MUST BE PROPERLY

GROUNDED.

Содержание FA23















Отзывы: