Page 6
SB-2-168-K
Fluid dripping or leaking from
bottom of cup
Runs and sags
Thin, sandy coarse finish drying
before it flows out
Thick, dimpled finish "orange peel"
TROUBLESHOOTING (continued)
CONDITION
CAUSE
CORRECTION
Cup loose on gun.
Cup gasket worn or missing below cup.
Cup threads dirty.
Too much material flow.
Material too thin.
Gun tilted on an angle, or gun
motion too slow.
Gun too far from surface.
Too much air pressure.
Improper thinner being used.
Gun too close to surface.
Air pressure too low.
Improper thinner being used.
Material not properly mixed.
Surface rough, oily, dirty.
Tighten.
Replace cup gasket.
Clean.
Adjust gun or reduce fluid flow.
Mix properly or apply light coats.
Hold gun at right angle to work and
adapt to proper gun technique.
Check distance. Normally approx. 8".
Reduce air pressure and check spray pattern.
Follow paint manufacturer's mixing instrs.
Check distance. Normally approx. 8".
Too much material coarsely atomized.
Increase air pressure or reduce fluid flow.
Follow paint manufacturer's mixing instrs.
Properly clean and prepare.
HAV-500 OR
HAV-511
Adjusting Valve
(HAV-511 SHOWN)
HAV-500 does not
have pressure gauge.
Use to control air
usage at gun.
GFC-501 (Acetal) 20 Oz. Cup
GFC-502 (Aluminum) 1 Liter Cup
Gravity Feed Cups
Joins any single
piece DeVilbiss air
cap with latest
version MBC-368,
MSA-1 or GTI-3
retaining rings.
Helps prevent parts
loss and provides
easier assembly.
JGA-156-K10
Spring Clips
These gravity feed cups
are designed to be used
with FLG, GFG, GFHV or
GTI gravity feed spray guns.
ACCESSORIES
MSP-524
Twin Cartridge,
Paint Spray
Respirator
NIOSH-Certified
(TC84A-1623) for respira-
tory protection in atmos-
pheres not immediately
dangerous to life.
GH-505 Gun
Holder
Gun holders are
made to hold stan-
dard paint cups, grav-
ity feed guns and
cups, and paint filters.
GTI-5033-2000
Air Cap Test Kit
The purpose of this test kit
is to measure air cap
atomizing air pressure at
the center air port of the air
cap. Used to confirm code
compliance and as a daily
quality control measure.
OMX-70-K48 Paint Cup Liner Kit
Consists of :
1 - Piercing Tool
48 - Disposable Liners
48 - Drain Bushings
Spray Gun Lube
SSL-10 (2 oz. bottle)
Compatible with all
paint materials;
contains no silicone
or petroleum distil-
lates to contami-
nate paint. MSDS
Sheet available
upon request.
Automotive Refinish Quick Connects
For HVLP Guns (Air)
High Flow Type.
HC-4720 Coupler
1/4" NPT(F)
HC-1166 Stem
1/4" NPT(M)
HC-4419 Stem
1/4" NPT(F)
HC-4719 Coupler
1/4" NPT(M) /NPS(M)
192212 Professional
Spray Gun
Cleaning Kit
Contains six preci-
sion tools designed
to effectively clean
all DeVilbiss, Binks,
Finishline and other
brand spray guns.
192219
Gun Holder
192218 Scrubs
®
Hand Cleaner Towels
Scrubs
®
are a pre-
moistened hand cleaner
towel for painters, body
men and mechanics that
go where you go and no
water is needed.
Gun holder made to
hold guns with
gravity cups.
HAF-507 Whirlwind™
In-Line Air Filter
WR-103 Wrench
Contains all necessary
tip, hose and nut sizes
used on or with gun.
Removes water, oil,
and debris from the
air line.
5/04 ©2004 Illinois Tool Works Inc. All rights reserved. Printed in U.S.A.
WARRANTY
This product is covered by DeVilbiss' 1 Year Limited
Warranty.
DeVilbiss Worldwide Sales and
Service Listing: www.devilbiss.com
ITW Automotive Refinishing
DeVilbiss has authorized distributors throughout the world.
For equipment, parts and service, check the Yellow Pages
under “Automotive Body Shop Equipment and Supplies.”
For technical assistance, see listing below.
U.S./Canada Customer Service Office:
1724 Indian Wood Circle, Suite J-K, Maumee, OH 43537
Toll-Free Telephone: 1-800-445-3988 (U.S.A. and Canada only)
Toll-Free Fax: 1-800-445-6643
Allows quick and
easy clean-up, and
also allows spraying
with the gun point-
ing upward.
