Connection and Adjustment
Lens Installation
Manual / Fixed Lens Mounting
1. If using a C-mount lens, attach the C-CS mount adaptor before installaing the lens.
2. Move the back focus adjustment lever fully to the left, with the lens facing towards you
(see Back Focus Adjustment).
3. Install the lens on to the camera.
4. Adjust the Back Focus to the correct positon then secure the screw.
5. Adjust the Zoom and Focus levers of the lens to acquire a clear image and the
required field of view.
Auto IRIS Lens Mounting
1. If using a C-mount lens, attach the C-CS mount adaptor before installaing the lens.
2. Move the back focus adjustment lever fully to the left, with the lens facing towards you
(see Back Focus Adjustment).
3. Install the lens on to the camera.
4. For Direct Drive Lens application, connect the DC Lens Connector to the rear panel of the camera.
Fit the lens to the camera according to the following connection assignments.
5. For Video Drive Lens application, connect the wires to the rear panel of the camera. Fit the lens to the
camera according to the following connection assignments.
Strip 6mm of insulation from lens wires. Depress button to open cable clamp aperture and insert bare end
into clamp. Release button to secure wire.
6. Adjust the Back Focus to the correct positon then secure the screw.
7. Adjust the Zoom and Focus levers of the lens to acquire a clear image and the required field of view
8. Adjust the Zoom and Focus levers of the lens to acquire the clear image.
Protective
Cover
Back Focus
Adjustment Lever
Lens
(Not Supplied)
C-CS Mount
(for C-type Lens)
Zoom and Focus
Adjustment Levers
Back Focus
Adjustment Lever
Lens (Optional)
Zoom and Focus
Adjustment Levers
DC Lens
Pin Assignments
Back Focus
Adjustment Lever
Lens (Not Supplied)
Zoom and Focus
Adjustment Levers
Pin Number
DC Drive
Pin 1
Damp
-
Pin 2
Damp +
Pin 3
Drive +
Pin 4
Drive -
2
1
4
3
Installing the Lens
Before installing a lens, you must first
remove the protective cover from the
camera. If mounting a C-Mount lens,
attach the C-CS mount adaptor to
the camera.
Adjust the Back Focus to acquire a
sharp image (see Back Focus
Adjustment).
Back Focus Adjustment
There is a mechanism for back focus adjustment.
Loosen the back focus locking screw.
Move the adjustment lever to obtain optimum focus of
the image.
Tighten the screw to lock the back focus
adjustment lever in place.
Back Focus Adjustment Lever
Rt
NO
Camera Configuration
DC Lens
Connector
Rt
NO
Video Lens
Pin Assignments
Button
Press to Open
the Clamp
Cable Clamp
SET
Control Key
ENTER Button
Navigation Pad
Camera OSD Menu
The control buttons are on the left hand side of the camera.
Push the side cover to access the buttons.
Press the
ENTER
button and the OSD Menu will be displayed.
Use the
Navigation Pad
to select the desired menu option.
Pressing the
ENTER
button will open the sub-menu or confirm the configuration.
Use the
Navigation Pad
to move the cursor to
SAVE
, then press
ENTER
button to write the new settings to
memory and complete the configuration.
To quit or give up the configuration, select
CANCEL
and press
ENTER
to close the OSD Menu.
To reset the camera to the factory setting, press the
Navigation Pad
and move the cursor to
DEFAULT
to
restore the factory setting.
DAY/NIGHT
DAY MODE
NIGHT MODE
LENS
LANGUAGE
WHITE BALANCE
3D DNR
SLOW SHUTTER
PAGE 2
AUTO
SETTING
SETTING
LEVEL
ENGLISH
AWB
AUTO
OFF
SAVE
CANCEL
DEFAULT
SET UP MENU 1
DAY/NIGHT
DAY MODE
NIGHT MODE
LENS
LANGUAGE
WHITE BALANCE
3D DNR
SLOW SHUTTER
SYNC
BLC
TITLE
PRIVACY ZONE
RS485
DIGITAL ZOOM
DETECTION
REVERSE
SAVE
AUTO
NIGHT
DAY
SETTING
BF
LEVEL
ENGLISH
FRANÇAIS
ESPAÑOL
中文
AWB
AWB-EX
MWB
PUSH MWB
AWB-SPEED
AUTO
OFF
LOW
HIGH
DVR
OFF
X02/X04/X08/X16
X32/X64/X128/X256
INT
LINE LOCK
OFF
ZONE 1
ZONE 2
ZONE 3
ZONE 4
ZONE 5
ZONE 6
OFF
ON
SETTING
SETTING
x1 / x1.5
x2 / x4 / x8
SETTING
OFF
H REVERSE
V REVERSE
HV REVERSE
CANCEL
D/N LEVEL
N/D LEVEL
BURST
D/N TIME
SHUTTER
BRIGHT
AGC
APERTURE
CHROMA
GAMMA CORR.
RES. ENCHANCE
LEVEL 1-19
R GAIN LEVEL
G GAIN LEVEL
SET
LEVEL
V-PHASE
LEVEL 1-15
TEXT
POSITION
FLASH
MASK MODE
LEVEL
POSITION
ALL CLEAR
ADDRESS
BAUD RATE
DETECT MODE
ZONE DISPLAY
ALARM TRIGGER
ZONE
DEFAULT
HIGH
STANDARD
LOW
AUTO / ON
5 Sec
10 Sec
20 Sec
30 Sec
60 Sec
1/50 (1/60)
1/120 (1/100)FLK
1/250
1/500
1/1K
1/2K
1/4K
1/10K
AES
WDR
LEVEL 1-15
LEVEL 1-8
STANDARD
ENHANCE
ENHANCE-EX
0 ~ 255
LOCK
PUSH ON
LOW
HIGH
STANDARD
(16 Characters)
OFF / ON
MASK / MOSAIC
LEVEL 1-15
ZONE 1
ZONE 2
ZONE 3
ZONE 4
0~999
4800 BPS
9600 BPS
19200 BPS
OFF
MOTION
FACE ZONE
FACE
REMAIN
AUTO
HIGH
LOW
SHADOW
HIGHLIGHT
LEVEL 1-15
LEVEL 1-15
