background image

E-1

INSTALLATION MANUAL

A0U4955022

PF-602 

Paper Feed Unit

Note:

    • Take the same procedures, though the machi-

nephotographs are different from the ones illus-
tratedin the procedures.

    • Lifting the machine in an awkward position or

transporting it in a poorly balanced position
could result in personal injury. When transport-
ing the machine, assign an adequate number of
persons to the job and ensure that each person
can take a good position of not being exces-
sively loaded. 
(mass: approx. 170 kg)

I.Directions for Placing the Machine on the Floor

Note:

When moving the PF-602, do not hold the area
indicated in the photograph below.

Note:

Make sure to conduct the procedure at each person.

1. Raising the front side of PF-602, to remove the 2

cushions.

2. Raising the back side of PF-602, remove the 2

cushions.

3. Fix the veneer with its beveled portion turned

upward, to the right end face of the pallet by nails
as illustrated below.

4. Set the 2 cushions removed from the machine,below

the veneer as illustrated below.

00AAIXE000SA

A03XIXJ001CB

A03XIXJ001CB

A03XIXE001CC

Do not hold here

A03XIXE017SA

Cushions

A03XIXE018SA

Cushions

Nails : 2 pcs.

Veneer

Corrugated fiberboard

A03XIXE019SA

A

D

C

B

B

C

A03XIXC014SA

Applied Machine: C6501/C6501P/C65hc/C7000/C7000P/C6000/C70hc
COLOR MFP: 65ppm COLOR PRESS: (71ppm/71ppm)/(70ppm/70ppm)/(60ppm/60ppm)
Product Code: A0U0/A0U2/A0Y8/A1DU/A204/A1DV/A205

Содержание PF-602









Отзывы: