Develcon Electronics DI-1135 Скачать руководство пользователя страница 54

Страница: 54 / 74

Event Logs

A-12 — Orbitor 3000 Reference Manual

* IPX Routing is disabled

Generated when IPX routing is disabled. This may be because operator command or an invalid
configuration between WAN interconnected devices.

* IPX Routing is enabled

Generated when IPX routing is enabled because WAN interconnected devices have compatible IPX
configurations.

* IPX: service table full

Generated when the IPX SAP table has been filled. Any new SAP frames received will be discarded.

* IPX: Link X, unknown RIP packet

Generated when the device receives an invalid RIP packet.

* IPX: Link X, unknown SAP packet

Generated when the device receives an invalid SAP packet.

* ISDN interface deactivated

Generated when the ISDN link module has lost a physical connection to the NT-1.

* ISDN interface activated

Generated when the ISDN link module has established a physical connection to the NT-1.

* LAN connection established

Generated on startup when integrity of the LAN interface has been successfully verified by the external
loopback test.

* LAN started forwarding

Generated when LAN forwarding is activated.

* LAN stopped forwarding

Generated when LAN forwarding is deactivated.

* LAN X adapter did not start

Generated when LANCE failed to start operation.

* LAN X adapter init timed out

Generated when LANCE initialization failure is detected.

* LAN X adapter stopped, restarting

Generated when the LANCE is detected to have stopped.

Содержание DI-1135










































































Результаты поиска

Содержание DI-1135

Отзывы:

Бренды по названию

Популярные бренды

Develcon Electronics DI-1135, Справочное руководство

Результаты поиска

Содержание DI-1135

Отзывы:

Бренды по названию

Популярные бренды