1.Securely fasten the bracket to the mounting surface using the fixing in the bracket.
2.Fix in the required angular postion by tightening the fixing bolt on the bracket at the
rear of the heater.
3.The bracket can be used to adjust the direction of the heater up and down (See Fig.
2 ).
This is done by loosening the bolts fixing the heater to the bracket,
and then
retightening once the correct position is a chieved.
Always
isolate
the
heater
from
the
mains
supply
when
adjusting
the
angular
position
.
·
In the event of heater failure, or for spare parts or advice,
please contact the
manufacture in the first instance.
·
Disconnect from the mains before commencing any maintenance procedure
including cleaning.
·
To ensure optimum heat effectiveness,
it is recommended that after the heater has
be enused for approximately 80-100 hours,
that the guard and lamp are removed and
there flector is wiped with a lint-free cloth before reassembling.
·
If the supply cord be comes damaged,
it must be replaced by the manufacturer,
its
service agent or a similar qualified person.
Caution:
Do not handle lamp with bare hands
.
Remove finger marks with a sof
tcloth and methylated spirits or alcohol
.
Finger marks will burn into quartz causing
premature lamp failure
.
Correct
Disposal
of
this
product
This marking indicates that this product should not be disposed with other
household wastes throughout the EU. To prevent possible harm to the
environment or human health from uncontrolled waste disposal, recycle it
responsibly to promote the sustainable reuse of material resources. To
return your used device, please use the return and collection systems or
contact the retailer where the product was purchased. They can take this
product for environmental safe recycling.
Rio outer casing can reach high temperatures.
Disposal
of
Waste
Electrical
and
Electronic
Equipment
This symbol on the product or on its packaging indicates that this product should not be
disposed of with your normal household waste.
The separate collection and recycling of
your waste electrical equipment at the time of its disposal will help to conserve natural
resources and ensure that it is recycled in a manner that protects human health and the
environment.
Specific Safety Instructions
WARNINGS
Do not use the heater in areas where
there is a risk of explosion or fire from
flammable gases. Ensure that the heating area
is kept clear of combustible materials. Do not
use the heater in damp areas, without suitable
ventilation. This heater is not designed for use
within 1m or above a water source. Do not place
within one metre (1m) of any water source. Do
not place directly in front of, below or above any
power points or switches.
Fire risk exists if this heater is covered by
or positioned close to curtains or other
combustible materials.
• This heater is intended for domestic/
household use only.
• Always ensure that this heater is installed as per
the requirements noted in Australian Standard
AS/NZS 3000:2007.
• Always keep heater at least one metre (1m)
from combustible materials.
• DO NOT locate this heater directly below,
above or in front of the power supply socket
or switch.
• DO NOT use this heater within 1 metre
or above any water source.
• DO NOT use this heater in either the
bathroom or ensuite without suitable
ventilation.
• DO NOT use a 3rd party timer, or
programmable system with this heater.
• DO NOT clean the heater while the heater is
on or plugged into the mains power supply.
• DO NOT touch any part of the heater while
on, hot surfaces may burn.
• DO NOT use the wall heater as a dryer.
• DO NOT attempt to modify the heater,
power cord, power plug or the supplied
accessories in any way.
• DO NOT expose the heater to rain, water, or
use in damp wet conditions.
• NEVER cover this heater.
• NEVER carry the heater by its power supply cord.
• NEVER use with the power cord coiled,
bundled up or tied up. Always extend fully
before use.
• NEVER use the heater if any part of it is
damaged.
• Ensure that the heater is disconnected from
the mains supply when installing, cleaning
or removing/installing.
• Ensure this heater is not left on when
unattended.
• Ensure the heater is not used in areas
where flammable gases are present, e.g.
paint, petrol etc.
• Always turn the heater OFF at the power
point switch when not in use for extended
periods of time.
• Always allow the heater to cool, about one
(1) hour after the heater has been turned
off, before cleaning the heater.
• Always ensure that the power cord is fully
extended and NOT in contact with any part
of the heater.
• Always ensure that the heater is kept clean
and free from dust.
• Only use this heater when securely attached
to the wall.
• Do not look directly at the heater when
it is on.
