Detroit Radiant Products Re-Verber-Ray DTH Series Скачать руководство пользователя страница 1

TUBE HEATER

TROUBLESHOOTING GUIDE

MODELS: DTH(S) Series Tube Heater

er

Detroit Radiant Products Company

21400 Hoover Road • Warren • Michigan • 48089 • (586) 756-0950 • Fax: (586) 756-2626

website:  www.reverberray.com         email:  [email protected]

THESE HEATERS 

MUST

 BE INSTALLED AND SERVICED BY TRAINED GAS

INSTALLATION AND SERVICE PERSONNEL ONLY.  READ AND UNDERSTAND ALL
INSTRUCTIONS THOROUGHLY BEFORE ATTEMPTING TO INSTALL, OPERATE OR
SERVICE THE DETROIT RADIANT PRODUCTS COMPANY HEATER.  FAILURE TO
COMPLY WITH THESE WARNINGS AND INSTRUCTIONS, AND THOSE ON THE
HEATER, COULD RESULT IN PERSONAL INJURY, DEATH, FIRE, ASPHYXIATION AND/
OR PROPERTY DAMAGE.  RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.

CAUTION!  Heater may be hot.  Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any other appliance.  Note presence of
flammable gas and electrical shock hazard.

WARNING!  Extinguish open flame while servicing heaters. Test for gas leaks with
soap and water solution only.  Wear safety glasses while servicing unit.

Approval Standards and Certifications

Detroit Radiant Products units comply with or are certified by the following Organizations
or Standards:

- American National Standards (ANSI Z83.6)
- Occupational Safety and Health Act (OSHA)
- American Gas Association (AGA)
- International Approval Services (IAS)

FOR YOUR SAFETY!

IF YOU SMELL GAS:
1. Open windows.
2. Do not touch electrical switches.
3. Extinguish any open flame.
4. Immediately call your gas supplier.

SHUTDOWN INSTRUCTIONS!

1. Open electrical circuit.

2. Rotate heater’s manual gas
valve knob to “OFF” position.

IMPORTANT

:

  

Any alteration of the system or of the factory-authorized components specified

either in this manual or by Detroit Radiant Products Company voids all certification and warranties.

Содержание Re-Verber-Ray DTH Series

























Отзывы: