Detex ADVANTEX 87 Series Скачать руководство пользователя страница 19

Страница: 19 / 20

STEP 14:

COVER INSTALLATIONS

DEVICE OPERATION TROUBLESHOOTING

Device not latching

when door closes

Latches release, but pushpad

will not fully depress

Latches are not releasing when
pushpad is fully depressed

Bottom bolt is not properly aligned with bottom strike hole.

Top strike insert is not installed or not correctly aligned with
the holdback.

Through fasteners for trim (if applicable) are interfering with

internal centerlift assembly.

Rods improperly adjusted

Device centercase lift finger not inserted properly into

centerlift assembly.

Top adjustment screw is adjusted too far in the retracted
direction (CCW).

Device centercase lift finger not inserted properly into

centerlift assembly.

Top adjustment screw is adjusted too far in the extended
direction (CW).

Bottom adjustment screw is adjusted too far in the extended
direction (CCW).

Modify bottom strike hole for fit.

Install and/or position strike insert per instructions.

Loosen and re-position through screws to clear.

Adjust rods per instructions.

Remove device and re-install per instructions.

Remove device from backplate and re-install with
lift finger correctly inserted.

Rotate top adjustment screw in the extended

direction (CW) per FINE LATCH ADJUSTMENT

procedure.

Remove device from backplate and re-install with
lift finger correctly inserted.

Rotate top adjustment screw in the retracted

direction (CCW) per FINE LATCH ADJUSTMENT

procedure.

Rotate bottom adjustment screw in the retracted

direction (CW) per FINE LATCH ADJUSTMENT

procedure.

SOLUTION

POSSIBLE CAUSE

SYMPTOM

EC2

flush

endcap shown

104924 Page 19

INSTALL

centercase cover with
(4) flat head screws

IMPORTANT

TIGHTEN screws
at this end first

INSTALL

endcap with

(2) flat head screws

10-32 x 5/16"

6-32 x 3/8

14a

14b

Содержание ADVANTEX 87 Series





















Результаты поиска

Содержание ADVANTEX 87 Series

Отзывы:

Бренды по названию

Популярные бренды

Detex ADVANTEX 87 Series, Руководство по установке

Результаты поиска

Содержание ADVANTEX 87 Series

Отзывы:

Бренды по названию

Популярные бренды