Detcon CXT-DM Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 58

Detcon CXT-DM Скачать руководство пользователя страница 9

Model CXT-DM

CXT-DM Instruction Manual

Rev. 2.0

Page 5 of 54

Figure 7 Smart Battery Pack

Quad Battery Charger (Optional)

Detcon’s Smart Battery Pack can be charged as needed using Detcon’s optional Quad Battery Charger which
can charge up to four battery packs at one time.  The Quad Battery Charger comes with a plug-in AC/DC
adapter that plugs into a standard 100-240VAC outlet for power.  The DC end of the adapter plugs into the DC
power jack of the charger providing 24VDC. The Quad Battery Charger has four charging ports, each with 8-
pin Beau connectors for battery pack connection. The ports and connectors are keyed to prevent incorrect
positioning and connection. Each port has its own “FAULT” LED indicator and “CHARGE” LED indicator
and will display either a red light or green light depending on the status of each battery being charged.
Charging times will vary depending on the charge state of each battery pack, but a full charge of a depleted
battery pack can take up to 24 hours.

Figure 8 Quad Battery Charger

1.4.2

D Cell Lithium Battery Pack

The D Cell Lithium Battery Pack (Figure 9) contains five 3.6V Lithium Primary D size batteries which are not
re-chargeable. This battery pack provides the unit with 18 volts. The batteries are contained in a battery holder

mounted in Detconꞌs aluminum explosion proof condulet. The CXT-DM sensors will operate up to 9 months
before battery replacement is needed. The battery Pack and Terminal Board are housed in Detcon’s Aluminum

«
...
7
8
9
10
11
...
»

Содержание CXT-DM



























































Отзывы:

Нет отзывов