background image

DESCO WEST 

- 3651 Walnut Avenue, Chino, CA 91710 • (909) 627-8178

DESCO EAST 

- One Colgate Way, Canton, MA 02021-1407 • (781) 821-8370 • Website: 

Desco.com

TB-3054

 Page 3 of 6

© 2017 DESCO INDUSTRIES, INC.

Employee Owned

Features and Components

19236

 Multi-Mount Continuous Monitor, 220VAC

1  Multi-Mount Continuous Monitor

1  24VDC Power Adapter without Power Cord

09100

 Jewel® Elastic Wristband

1  6' Mat Monitor Cord (Black)

1  6' Mat Ground Cord (Green and Yellow)

2  Push and Clinch Snaps

2  Mounting Screws

2  Countersink Washers

1  Set of Hook and Loop Fasteners

1  Zip Tie

1  Certificate of Calibration

NOTE: The power cord must be purchased separately 

for Multi-Mount Monitor items 

19234

 and 

19236

 See 

the following EMIT items for available power cords:

Item

Power Cord Type

50545

Europe

50546

United Kingdom

Figure 2.  220VAC power adapter included with the 

Desco 

19234

 and 

19236

 Multi-Mount Continuous 

Monintors.  Power cord sold separately.

A

B

I

H

G

C

D

E

Figure 3.  Multi-Mount Continuous Monitor features and 

components

F

A. Status LEDs:

 When the green LED is illuminated, 

the operator is properly grounded.  When the red LED is 

illuminated, the operator is not properly grounded.

B. Monitored Operator Jack:

 Where the operator 

inserts the wrist cord banana plug.

C. Worksurface Ground LEDs: 

When the green LED 

is illuminated, the worksurface mat is properly grounded.  

When the red LED is illuminated, the worksurface mat is 

not properly grounded.

D. Operator Ground LEDs:

 When the green LED is 

illuminated, the operator is properly grounded.  When 

the red LED is illuminated, the operator is not properly 

grounded.

E. 4mm Parking Snap:

 When touched by the operator, 

this snap will deactivate the alarm for six seconds.  This 

allows time for the operator to disconnect the coil cord 

from the wrist band and park it on this snap.  While 

parked, the coil cord disables the alarm, allowing the 

operator to leave the workstation.  The OPERATOR 

GROUND LED will remain off while the cord is parked.  

Upon returning and removing the coil cord from the 

parking snap, the operator has six seconds to hook up 

to the wrist band before the alarm sounds.

F. Cable Tie Mount:

 Pair with the included zip tie to 

secure the nearby power adapter cord and reduce strain 

on its plug.

G. Power Jack:

 Connect the power adapter here.

H. Mat Connection:

 Monitors worksurface mat. 

NOTE: To disable worksurface monitoring, shunt this 

terminal to the neighboring GND terminal with bus wire.

I. Mat Ground:

 Grounds worksurface mat.

Содержание 19234








Отзывы: