background image

16

V E N T - F R E E   G A S   H E A T E R   S E R V I C E   M A N U A L

COLD-START CHOKE ADJUSTMENT

GRH/OV 027

Pilot ignites but will not stay lit

Possible Causes

1.

Control knob not held down long enough

2.

Defective valve or thermocouple

3.

Not enough fresh air

4.

Wrong air/gas mixture at pilot

Procedures

1. Be sure that the control knob is held down

long enough to get the thermocouple hot.
After lighting the pilot, hold the control
knob down for 10 to 15 seconds before
releasing.

2. Check to be sure that the pilot flame pat-

tern is correct (see Figures 15 & 16).

Figure 15. Correct LP Pilot Flame

Figure 16. Correct Natural Gas Pilot Flame

If the pilot flame appears to be normal,
check the control valve according to the
test procedure outlined on page 12 under
“Testing Control Valve and Thermocouple”.
If the valve passes the testing, the thermo-
couple may be defective and should be
replaced.

3. If the pilot flame is lifting off the thermo-

couple as shown in Figure 17, check to be
sure that the room is properly ventilated.
See 

“SPECIFICATIONS”, page 13, for the

minimum fresh air openings required. If
necessary, instruct the user to slightly open
a window for proper ventilation.

4. Be sure that strong or gusty drafts are not

blowing on the heater. If necessary, the

GRH/OV 007

GOOD PILOT/LP

GRH/OV 009

GOOD PILOT

GRH/OV 008

BAD PILOT/LP

LP

GRH/OV 010

BAD PILOT

Natural Gas

Figure 18. Pilot Barrel Liftoff

LP

Figure 17. Pilot Barrel Liftoff

heater should be relocated to a more
protected area.

If the pilot flame is incorrect as shown in
Figure 18, it is possible that the cold-start
choke is allowing too much air to enter the
pilot tube. Turn the heater off, remove the
front cover from the heater, and inspect the
cold-start choke on the pilot tube.

Insert a 1/4 inch diameter rod (i.e., a 1/4
inch drill bit will do) under the bi-metal strip
to adjust the cold-start choke to the nearly
closed position (see Figure 19). Relight the
pilot and observe to see if the pilot flame is
more stable. Replace the front cover.

GRH/OV 007A

FLAME LIFTING/LP

Liftoff

LP

Figure 19. Cold-Start Choke Adjustment

GRH/OV 009A

FLAME LIFTING

Liftoff

Natural Gas

Figure 18. Thermocouple Liftoff

1/4" Rod

Содержание VP2600





















Отзывы: