background image

20

106573

DIRECT-VENT GAS FIREPLACE

EVDDVF36PN and EVDDVF36STN

®

OPERATING
GUIDELINES AND
MAINTENANCE
INSTRUCTIONS

When lit for the first time, the appliance may
emit a slight odor for about 16 - 24 hours. This
is normal and is due to the “curing” of the logs
and the “burn-in” of internal paints and lubri-
cants used in the manufacturing process.
Keep compartments, logs, burners, and area
surrounding the logs clean by vacuuming or
brushing at least twice a year. Temporary
removal of the log set may ease the cleaning
of the burner and electrode assembly. In
cleaning, take care not to alter the electrode or
burner location. Be sure appliance is cool
before each maintenance session.

 CAUTION: The appliance and

logs can get very hot - Handle
only when cool.

 WARNING: Do not operate

appliance with panel(s) and glass
removed, cracked, or broken. Re-
placement of the panel(s) should
be done by a licensed, qualified
service person.

 WARNING: Make certain wires

and gas lines are not touching
the underside of the firebox.

 CAUTION: If the glass breaks,

be cautious of fragments on the
floor. Keep children away from
the area. Do not operate the unit.
Use proper safety gloves to re-
move the broken glass door. Dis-
card safely. A glass door kit can
be ordered through your local
distributor. Do not substitute
other material for the glass.

 WARNING: Children and

adults should be alerted to the
hazards of high surface tempera-
tures, and to stay away from the
appliance to avoid burns or cloth-
ing ignition. Young children
should be carefully supervised
when they are in the same room
as the appliance.

 WARNING: Have a qualified

agency periodically inspect the
vent system at the start of each
heating season, for any obstruc-
tion which may hinder its normal
operation. Never obstruct the
flow of combustion and ventila-
tion air. Keep the front of the
appliance clear of all obstacles
and materials.

 WARNING: Do not abuse,

strike, or slam the glass doors.

 CAUTION: Label all wires

prior to disconnection when ser-
vicing controls. Wiring errors
can cause improper and danger-
ous operation.

For further operating guidelines, contact
your authorized dealer.

Any household glass cleaner may be used to
clean the glass panel. Do not use abrasive
cleaners as this may damage the glass. Clean
glass only when cool.

 WARNING: Turn off gas and

wall switch before servicing ap-
pliance. Any safety screen or
guard removed for servicing the
appliance must be replaced prior
to operating the appliance.

BURNER REMOVAL

 CAUTION: Before proceed-

ing, make sure the entire unit is
cool.

1.

Remove the top and bottom louvers and
screen. Open the glass door (left or right
side).

2.

Carefully remove the log set.

3.

Remove the screw that attaches the
burner to the bracket.

4.

Slide the burner towards the front of
the unit, lift, and remove from the fire-
box.

5.

To reinstall the burner, slide the burner
towards the rear of the unit and secure
burner to bracket with screw.

 CAUTION: Make certain the

orifice is inside the venturi tube's
air shutter, see Figure 50, page 19.

6.

Replace the log set, close door with
latches, and attach screen and louvers.

BURNER FLAME
ADJUSTMENT

Continued

Содержание Vanguard EVDDVF36PN





























Отзывы: