111162-01A
10
For more information, visit www.desatech.com
For more information, visit www.desatech.com
H
I
L
O
O
F
F
P
IL
OT
O
N
INSTALLING GAS LOG HEATER INTO STOVE
1.
Remove log and gas log heater from carton.
Note:
Do not pick
up gas log heater by the burner itself. This could damage heater.
Always handle the gas log heater by the heater base only.
2.
Remove all protective packaging applied to log and gas log heater
for shipment.
3.
Check all items for any shipping damage. If damaged, promptly
inform dealer where you bought heater.
4.
If not already removed, remove back panel from assembled
stove body (see Figure 5, page 8). Use an adjustable wrench or
a 10 mm socket. Remove six (6) bolts and washers. Keep bolts
and washers to reattach back panel later.
5.
Set gas log heater inside stove. Make sure control knob extension
passes through bottom front opening (see Figure 15).
6.
Align outside holes on heater base with four (4) mounting holes
on the stove bottom (see Figure 15).
INSTALLATION
Continued
CAUTION: Do not remove the data plates attached
to the heater base assembly. The data plates contain
important warranty and safety information.
WARNING: Failure to position the parts in accor-
dance with these diagrams or failure to use only parts
specifically approved with this heater may result in
property damage or personal injury.
CAUTION: After installation and periodically there-
after, check to ensure that no flame comes in contact
with any log. With the heater set to HI, check to see if
flames contact any log. If so, reposition logs accord-
ing to the log installation instructions in this manual.
Flames contacting logs will create soot.
Figure 15 - Placing Heater Base In Stove Cavity (Appearance
May Vary Depending on Model)
7.
Fasten heater base to stove bottom with #10-24 x .50 bolts and
hex nuts provided with gas log heater (see Figure 16). Attach-
ment hardware is factory packed inside plastic bag with instal-
lation manual and owner’s registration card. Push bolt through
heater base mounting hole and through stove bottom. Connect
hex nut to bolt on underside of stove bottom. The bolt hex
head is for a 5/16" socket and the hex nuts are for a 3/8" socket.
If sockets are not available, use adjustable wrenches.
8.
Set one-piece log on heater base as shown in Figure 17. Make
sure middle section at bottom of log is seated into "U" shaped
cutout in center of heater base. Log will fit securely on base.
IMPORTANT:
Make sure log does not cover any burner ports
and does not touch the stove cavity (see Figure 18).
9.
Fasten back panel to stove with six (6) M6 x 1.20mm bolts and
washers. Make sure product identification label is located on the
outside lower left-hand corner.
10. Place freestanding stove in desired position in room. Be sure
to maintain clearances to combustibles as outlined on page 7.
Figure 16 - Fastening Heater Base to Stove Drop Bottom
Burner Porting
Areas (double
slotted rectangular
openings)
Figure 18 - Top View of One-Piece Log Set on Gas Log Heater
Safety Pilot
Location
One-Piece
Log Set
One-Piece
Log Set
"U" Shaped Cutout
in Chassis
Burner
Middle Section at
Bottom of Log Set
Figure 17 - Installing One-Piece Stove Log Set (Remote-Ready
Log Heater Shown)
Heater
Base
Bottom
Front
Opening
Stove
Bottom
Burner
Bolt
Heater
Base
Stove Bottom
Heater Base
Bolt
Hex Nut
INSTALLATION
Stove Cavity Assembly (Cont.)
Installing Gas Log Heater Into Stove
