background image

www.desatech.com

116239-01F

30

Key Pad Lock Feature

This feature allows the user to lock/unlock the 

keypad on the hand-held remote in the MANU or 

AUTO mode to prevent inadvertent operation (i.e. 

children operating the hand-held remote control, 

etc.). The keypad is locked in either on or off. Press 

the POWER and LOCK buttons together to turn 

the unit on or off.

OpERATING OpTIONAL  

GWMT1 - WALL MOUNTED 

THERMOSTAT

  WARNING:  Do  not  con-

nect the thermostat to a power 

source. Electrical shock and/or 

a fire hazard will occur.

Light the fireplace as instructed in 

Lighting 

Instructions

 on page 27. Set wall thermostat to 

desired temperature. 

This thermostat has been electronically cali-

brated at the factory and requires no adjust-

ment or leveling.

Upon installation, the thermostat must be al-

lowed to stabilize at room temperature for a 

minimum of 30 minutes for proper operation.

To turn the fireplace off, adjust thermostat to 

the lowest setting and turn the gas control knob 

back to PILOT. The pilot will remain lit. 

IMPORTANT:

 To turn the pilot off, turn the 

gas control knob on the heater to the OFF 

position. 

OpERATING OpTIONAL 

BLOWER ACCESSORY

Locate the blower controls by opening the lower 

louver panel on the fireplace. Blower controls 

are  located  on  the  right  side  of  the  switch 

bracket to the left just inside the louver panel.

The BK manual blower and the BKT thermo-

statically-controlled blower have an ON setting 

and an OFF setting. The blower will only run 

when the switch is in the ON position. In the 

OFF position, the blower will not operate.

OPERATING FIREPLACE

Continued

Note  for  BKT  Only:

 If you are using BKT 

blower with optional thermostat (wall mounted 

or remote control) for the fireplace, your fire

-

place and blower will not turn on and off at the 

same time. The fireplace may run for several 

minutes before the blower turns on. After the 

heater modulates to the pilot position, the blow-

er will continue to run. The blower will shut off 

after the firebox temperature decreases.

The blower helps distribute heated air from 

the fireplace. Periodically check the louvers of 

the firebox and remove any dust, dirt or other 

obstructions that will hinder the flow of air.

INSPECTING bURNERS

Check pilot flame pattern and burner flame pat

-

terns often.

PILOT ASSEMBLY

The pilot assembly is factory preset for the proper 

flame height. Alterations may have occurred dur

-

ing shipping and handling. Call a qualified service 

person to readjust the pilot if necessary.

The height of the thermopile must be 3/8" to 1/2" 

above the pilot flame as shown in Figure 49. The 

thermocouple must be at a height of about 1/8" 

above the pilot flame. The flame from the pilot 

burner must extend beyond both the thermocouple 

and thermopile.

If you pilot assembly does not meet these require

-

ments:

•  turn fireplace off (see 

To Turn Off Gas to Ap-

pliance

, page 28)

•  see 

Troubleshooting

, page 33

Thermocouple

Thermopile

1/8"

Pilot Burner

Piezo
Ignitor

Figure 49 - Pilot Assembly

3/8" to 1/2"

Содержание KC42N Series













































Отзывы: