Desa FMI FVDA18M Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 24

Desa FMI FVDA18M Скачать руководство пользователя страница 8

www.desatech.com

124184-01B

8

INSTALLATION

Continued

Propane/LP Gas Conversion

To  convert  to  propane/LP  gas,  burner  inlet
fitting  and  pilot  orifice  must  be  replaced
and  regulator  pressure  must  be  reset.  Pro-
pane/LP  burner  inlet  fitting  is  supplied  with
orifice  installed.  Propane/LP  pilot  orifice  for
converting  pilot  is  supplied  and  is  marked
with a red stripe.
1.  Remove control rod extension and piezo

ignitor by pulling gently.

2. Remove screws that attach pilot assembly

to valve cover and valve cover to burner
pan (see Figure 7).

3. Remove valve cover.
4. Using a wrench, remove gas control valve

and burner inlet fitting by turning counter-
clockwise (see Figure 8).

Figure 9 - Burner Inlet Fittings with

Injectors

NATURAL
GAS
FITTING

PROPANE/LP
GAS FITTING

Injector
for Natural
Gas

Injector for
Propane/LP
Gas

5. Remove burner inlet fitting from gas control

assembly (see Figure 8). DO NOT remove
orifice from this fitting. Propane/LP burner
inlet fitting is included in hardware kit (see
Figure 9).

6. Be sure to use correct orifice for your

appliance. Orifice kit included with this
appliance contains an orifice installed in
an air mixer fitting.

7. Using thread sealant (resistant to the ac-

tion of propane/LP gas) on smaller end of
fitting, screw burner inlet fitting into outlet
side of gas control (see Figure 8). Tighten
using a wrench.

8. Thread gas control valve and burner inlet

fitting into burner manifold (see Figure 8).
Use thread sealant on male threads of
burner inlet fitting. Secure with a wrench.
Make sure control rod is facing the front
(see Figure 8).

9. To adjust regulator pressure, remove

the brass hex plug from regulator (see
Figure 10).

10. Remove the plastic pressure button from

the brass plug (see Figure 10).

11. Reverse the plastic pressure button

and replace it into the brass plug (see
Figure 10).

Piezo
Ignitor

Control Rod
Extension

Screw

Valve Cover

Control
Knob

Figure 7 - Removing/Installing Cover,

Control Knob, and Piezo Ignitor

Thermocouple

Ignitor

Pilot

Figure 8- Remove Burner Inlet Fitting

Burner Inlet
Fitting for
Natural Gas

Control Rod

Control
Valve

Figure 10 - Adjusting Regulator Pressure

for Conversion

Reversed
Plastic Pressure
Button for
Propane/LP
Conversion

Plastic Pressure
Button Positioned
for Natural Gas

Regulator

Brass Plug

«
...
6
7
8
9
10
...
»

Содержание FMI FVDA18M

























Отзывы:

Нет отзывов