background image

22

201835

DIRECT-VENT NATURAL GAS HEATER

DYNAVENT

®

ILLUSTRATED
PARTS LIST

CABINET ASSEMBLY
40,000 BTU/HR MODEL

This list contains replaceable parts used in your furnace. When ordering parts, follow the
instructions listed under Replacement Parts on page 19 of this manual.

2

5

6

1

7

4

9

8   

10

SOLID STATE       IGNITION

50   60   70   80   90

50   60   70   80   90

3

KEY

PART

NO.

NUMBER

DESCRIPTION

QTY.

1

280498

Bottom Shield

1

2

121520

Screw, #8 x 3/8" **

2

3

191241

Front Cover Trim*

1

4

030642

Front Cover Assembly

1

5

100896

Cabinet Assembly

1

6

070511

Cabinet Insulation (right and left sides)

1

7

120158

Screw, #8 x 3/8" **

2

8

160912

Thermostat (includes 2 screws)

1

9

121224

Screw, #10 x 3/4" **

4

10

062242

Thermostat Mounting Plate

1

070541

Cabinet Insulation (back)

1

070510

Cabinet Insulation (top)

1

191245

Operating Instructions Decal (English)

1

191247

Operating Instructions Decal (French)

1

531010

Warning Decal

1

191262

Nameplate

1

 Parts available, not shown.

* You must order nameplate and operating instructions decal separately.
** Standard hardware, available at local hardware store.

Содержание DynaVent DNV25NB































Отзывы: