Desa Comfort Glow CCL3018NTA Скачать руководство пользователя

Страница: 1 / 36

UNVENTED (VENT-FREE) GAS LOG HEATER

OWNER’S OPERATION AND INSTALLATION MANUAL

Biltmore Split Oak, Seasonal Oak and Smoky Mountain Oak Logs

Variable Manually-Controlled Models Also

Design-Certified As Vented Decorative Appliances

18", 24" AND 30" VARIAbLE

MANUALLy-CONTROLLED

MODELS

CRL2718PA/NA
CRL3124PA/NA

18", 24" AND 30"

THERMOSTATICALLy-CONTROLLED

MODELS

CCL3018PTA/NTA
CCL3924PTA/NTA

Patent Pending

PIL

REMOTE

OFF

For more information, visit www.desatech.com

WARNING: If the information in this manual is not

followed exactly, a fire or explosion may result causing

property damage, personal injury or loss of life.

— Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any other

appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any

phone in your building.

• Immediately call your gas supplier from a neighbor’s

phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the fire

department.

— Installation and service must be performed by a quali

fied installer, service agency or the gas supplier.

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

Содержание Comfort Glow CCL3018NTA





































Результаты поиска

Содержание Comfort Glow CCL3018NTA

Отзывы:

Похожие инструкции для Comfort Glow CCL3018NTA

Бренды по названию

Популярные бренды

Desa Comfort Glow CCL3018NTA, Руководство владельца по эксплуатации и установке

Результаты поиска

Содержание Comfort Glow CCL3018NTA

Отзывы:

Похожие инструкции для Comfort Glow CCL3018NTA

Бренды по названию

Популярные бренды