Manufacturer
DeRoyal
200 DeBusk Lane, Powell, TN 37849 U.S.A.
888.938.7828
©2006 DeRoyal. All Rights Reserved.
Part #1-4300/05
Revision 09 Revised 8/06
Patent Pending
Adjusting the toe piece
Adjust the length of the toe piece
by loosening the thumb knob on
the under side of the sole. Position
the toe piece to the desired length,
and retighten the knob. The toe
piece can also be adjusted to either side of the
foot, to prevent pressure sores in those areas. NOTE:
The thumb knob does not detach from the Boot.
Adjusting the Anti-rotation Bar
Rotate the bar clock-wise or
counter clock-wise to the desired
position. This will assist in the
prevention of inversion or eversion.
Attaching and Removing the Boot Sole
To apply, place the Boot Sole on bottom of the
frame, aligning the hole in the sole with the thumb
knob. With thumbs on either
side of the hole, push the sole
down and toward the heel. The
thumb knob will slide to the back
of the slot on the sole. Push
down on the sole at the heel until
it locks into place. To remove,
position the fingers between the
sole and the frame at the heel.
Push the heel of the hand against
the sole while pulling the sole
away from the frame with the
fingers until it unsnaps. Slide the
sole toward the toes until the
thumb knob is even with the hole,
and remove.
LINER OPTIONS
The single piece Vel-foam liner comfortably wraps
around the foot and ankle, and allows airflow. Hook
and loop closures make donning and doffing of the
boot easy.
The single piece 1” Fleece liner offers maximum
comfort for the patient. This is especially important
for patients with a tendency of skin shear. Hook and
loop closures allow for easy donning and doffing of
the boot.
Each Ankle Contracture Boot is supplied with a
mesh laundry bag. The liners can be machine
washed and dried.
REPLACING LINERS
1. To remove the liners, pull
the toe and anti-rotation
bar covers off. Unfasten the
hook and loop closure at the
back of the heel and pull the
foot cuff forward off the
plastic frame.
2. Pull the calf portion of
the liner up and off of
the frame.
3. To apply the liners, slide
the calf of the frame into the calf pocket of the
liner. Slide the foot of the frame into the foot
pocket of the liner. Secure the hook and loop
closure at the back of the heel. Slide the covers
over the anti-rotation bar and toe piece.
SIZING
Measure circumference calf
foot
B
10" – 14"
7" – 9"
C
14" – 16"
9" – 11"
D
16" – 21"
11" – 13"
E
16" – 21"
13" +
OPTIONS
Hip Abduction Bar
4300/05AB
Boot Sole
4300/05WK
Fleece Softgoods
4305K
Vel-foam
™
Softgoods 4300K
WASHING INSTRUCTIONS
Remove all liner pieces and fasten all hook and loop
closures. Place in mesh laundry bag. Machine wash
with mild detergent and warm water. Use no bleach.
Rinse and tumble dry. Liners can be washed but not
sterilized. Single Patient Use Only.
1
2
1
Manufacturer
DeRoyal
200 DeBusk Lane, Powell, TN 37849 U.S.A.
888.938.7828
©2006 DeRoyal. All Rights Reserved.
Part #1-4300/05
Revision 09 Revised 8/06
Patent Pending
Adjusting the toe piece
Adjust the length of the toe piece
by loosening the thumb knob on
the under side of the sole. Position
the toe piece to the desired length,
and retighten the knob. The toe
piece can also be adjusted to either side of the
foot, to prevent pressure sores in those areas. NOTE:
The thumb knob does not detach from the Boot.
Adjusting the Anti-rotation Bar
Rotate the bar clock-wise or
counter clock-wise to the desired
position. This will assist in the
prevention of inversion or eversion.
Attaching and Removing the Boot Sole
To apply, place the Boot Sole on bottom of the
frame, aligning the hole in the sole with the thumb
knob. With thumbs on either
side of the hole, push the sole
down and toward the heel. The
thumb knob will slide to the back
of the slot on the sole. Push
down on the sole at the heel until
it locks into place. To remove,
position the fingers between the
sole and the frame at the heel.
Push the heel of the hand against
the sole while pulling the sole
away from the frame with the
fingers until it unsnaps. Slide the
sole toward the toes until the
thumb knob is even with the hole,
and remove.
LINER OPTIONS
The single piece Vel-foam liner comfortably wraps
around the foot and ankle, and allows airflow. Hook
and loop closures make donning and doffing of the
boot easy.
The single piece 1” Fleece liner offers maximum
comfort for the patient. This is especially important
for patients with a tendency of skin shear. Hook and
loop closures allow for easy donning and doffing of
the boot.
Each Ankle Contracture Boot is supplied with a
mesh laundry bag. The liners can be machine
washed and dried.
REPLACING LINERS
1. To remove the liners, pull
the toe and anti-rotation
bar covers off. Unfasten the
hook and loop closure at the
back of the heel and pull the
foot cuff forward off the
plastic frame.
2. Pull the calf portion of
the liner up and off of
the frame.
3. To apply the liners, slide
the calf of the frame into the calf pocket of the
liner. Slide the foot of the frame into the foot
pocket of the liner. Secure the hook and loop
closure at the back of the heel. Slide the covers
over the anti-rotation bar and toe piece.
SIZING
Measure circumference calf
foot
B
10" – 14"
7" – 9"
C
14" – 16"
9" – 11"
D
16" – 21"
11" – 13"
E
16" – 21"
13" +
OPTIONS
Hip Abduction Bar
4300/05AB
Boot Sole
4300/05WK
Fleece Softgoods
4305K
Vel-foam
™
Softgoods 4300K
WASHING INSTRUCTIONS
Remove all liner pieces and fasten all hook and loop
closures. Place in mesh laundry bag. Machine wash
with mild detergent and warm water. Use no bleach.
Rinse and tumble dry. Liners can be washed but not
sterilized. Single Patient Use Only.
1
2
1