DERALE PERFPORMANCE
SENSOR
OVERRIDE
BA
TT
E
R
Y
SENSOR
FA
N
BA
TT
E
R
Y
CA
LI
B
R
ATI
O
N
POTE
NT
OM
ETE
R
MUL
T
ME
TER
FA
N
S
S
( )
A
C
U S PA ENT 700 762 MADE N USA
S
( )
( )
2. Route the 10
Red Wire now connected to the battery to the Circuit Breaker previously installed and cut the wire to the
AWG
appropriate length.
3. Using a Yellow #
Ring Terminal, connect the 10
Red Wire to the “
” Terminal on the Circuit Breaker.
10
AWG
BAT
4. Using a Yellow #
Ring Terminal, connect the auxiliary side “
” of the circuit breaker to another length of 10
Red Wire.
10
AUX
AWG
5. Route the Red 10
wire now connected to the auxiliary side of the circuit breaker to the Positive (+) Battery Terminal on
AWG
the Control Module Circuit Board and connect using a Yellow # Ring Terminal.
8
6. Using the Red 10
wire and a Yellow # Ring Terminal, connect into the positive (+) Fan Terminal on the Control Module.
AWG
8
7. Using a Yellow Butt Connector, connect the loose end of the Red 10 AWG wire connected to the Control Module positive (+)
Fan Terminal, connect to the positive (+) side of the fan(s). (If connecting to a Two Speed single Shrouded Derale Fan,
connect to the positive (+) Brown wire and Gray wire on the Electric Fan. See Diagram #8 and on page 5 diagram #10).
8. Using a # Yellow Ring Terminal, connect the 10
Black wire to the Negative (-) Terminal on the Control Module. Route
8
AWG
the other end of the wire to the Negative terminal on the vehicles battery & connect
. Do not
using a 5/16 Yellow Ring Terminal
connect to a chassis ground.
9. Using a Yellow Butt Connector, connect the 10
Black wire to the Negative (-) lead of the fan(s).
the other end of
AWG
Connect
this wire to the fan (-) terminal of the Module using
#8 Yellow Ring Terminal.
a
Green Wire: Override Circuit (Optional)
The green wire is designed to work in two different configurations. When used, this will allow the Electric Fan(s) to be turned on
regardless of the temperature of the thermostat. The fan speed will quickly ramp up to 60% and will operate between 60 and
100% as the temperature increases.
Use of the Override terminal is optional and not required for the
Control Module
Note:
PWM
to work properly.
1.
A/C Override - Using the
provided, attach the green wire to a Positive (+) 12V output on the
Blue Wire Tap Connector
A/C
compressor.
2.
Manual Switch Override - Attach the Green Wire to the 12V output on the manual switch (not provided).
B
.
AT
To Battery
12V (+)
Sensor
Two Wire
Circuit
Breaker
AUX.
Battery (-)
Fan (+)
Fan (-)
Override Circuit
12V (+)
Electric
Fan(s)
Attach Red wire
to positive (+)
Fan Terminal on
Control Module
Yellow #8
Ring Terminal
Dual FAN
Single Two Speed FAN
Gray (+)
Low Speed
Brown (+)
High Speed
Fan(s) (+)
Fan(s) ( )
Yellow #8
Ring Terminal
Attach Red wire
to positive (+)
Fan Terminal on
Control Module
Fan(s) ( )
Attach Black wire
to negative ( )
Fan Terminal on
Control Module
Attach Black wire
to negative ( )
Fan Terminal on
Control Module
To Sensor
Probe
B
.
AT
Circuit
Breaker
AUX.
Electric
Fan(s)
Warning:
When following steps 5 and 8, Only connect Battery Positive and Negative Leads direct to Battery. Do not
connect to Alternator or Starter. Failure to connect to Battery will Void the Warranty.
Flat Washer
Shoulder Washer
Nut*
Diagram #6
Nut
+
Split Washer
Terminal
Terminal
+
Do not exceed 12 inch lbs. of torque
when tightening terminal nuts
Please See Quick Reference Guide
for a Wiring Diagram on page 5.
WIRING CONTROL MODULE & ELECTRIC FAN
Before starting, disconnect the Negative (-) cable on the vehicles battery. Using the
electrical connectors
wire ties provided, follow the instructions below. (See Dia. #6 for
&
proper lug stacking) Before installing the shroud into the vehicle, the
ontrol
odule must
(
C
M
be installed. Remove all pieces from the package and locate the
, 6-32 x 1/4” BH allen
two
bolts. If installing onto a single shroud
and
,
two
the provided Corner Mounting Bracket
8-32 x 1/4” BH allen
hese will be used to fasten the
ontrol
bolts will be used also. T
C
M
on page
& on page
Dia.
.
odule to the shroud as shown
s 2 or 3
5
#11 Once securely
attached to shroud, you may connect the fan(s) wires to the module by following steps 6-9
of the installation section).
1. Using a Yellow 5/16 Ring Terminal & 10 AWG Red Wire supplied, connect one end of the
red wire to the vehicles Positive (+) terminal on the battery.
( age 3
P
)
*Factory thread sealed
Nut.
All
Do not remove.
Terminal wires must be
installed above this nut.
Diagram #7
Brown & Gray wires for 2 speeds (+)
or Red wires for one speed Fans (+)
Diagram #8
