6
ENGLISH
!7
Input select switch
• Switches between the PHONO/LINE and LINE
inputs.
• When the lever of switch is vertical position, the
LINE2 or LINE4 input is selected.
• When the lever of switch is slope, the
PHONO1/LINE1 or PHONO2/lINE3 input is
selected.
• You can perform 8 direction placement. See
page 10.
!8
SPLIT CUE button
• In the STEREO mode, the stereo sound of
MASTER and CUE are fed to both ear cups. In
the SPLIT CUE mode, the headphone circuit
provides monaural CUE sound to the left and
monaural MASTER sound to the right.
• When the Level Meter mode select switch is
set to “MASTER”…In the STEREO mode, the
meter indicates the stereo level in the L/R
Master output. In the SPLIT CUE mode, the
monaural CUE sound level is displayed on the
left and the monaural MASTER sound level is
displayed on the right.
• In the SPLIT CUE mode, the LED is lit.
!9
PGM 1/2 KILLS switches
• These switches are used cut out the Treble, Mid
or Bass frequencies of the incoming audio
signal. When these switches moved up or
down, the selected frequency level is cut, the
LED located directly above the specific switch
will glow indicating the cut function has been
activated.
@0
Level meter mode select switch
• The position of this switch will determine the
Level Meter mode. In the “MASTER” position,
the meter will detail the out level of the left and
right channels. In the “PGM 1/2” position, the
left side of the meter will indicate monaural
level of the PGM 1 and the right side of the
meter will indicate monaural level of the PGM 2.
@1
Channel Fader
• Controls the channel output level.
@2
Level meter
• The dual LED's indicators are used to detail
either the master output level, a combination of
the master output level and the CUE signal
level, or the PGM1/2 monaural level.
@3
Crossfader
• Fades the overall mixer output between
channels 1 and 2.
(2) Rear panel
@4
Power operation switch (POWER)
• Selects power “ON” or “OFF”.
NOTE:
Whenever the power switch is in the OFF state,
the AC adaptor is still connected on AC line
voltage. Please be sure to unplug the cord when
you don’t use for along time.
@5
BALANCED MASTER OUT jacks
• These 1/4” TRS jacks provide a balanced line
level output.
• Connect these jacks to the balanced analog
input jacks on an amplifier or console.
• Pin layout: Tip=Hot Ring=Cold Sleeve=GND
@6
EFFECT LOOP SEND/RETURN jacks
• These 1/4” TS stereo jacks allow external
processing of the program signal.
• When connect monaural type effect processor,
use Lch input and output.
@7
MIC BALANCED INPUT jack
• Accepts an balanced microphone with 1/4” TRS
mono jacks.
• Pin layout: Tip=Hot Ring=Cold Sleeve=GND
@8
MIC EFFECT LOOP jack
• These 1/4” TRS jack allow external processing
of the program signal.
• Pin layout:
Tip=SEND Ring=RETURN Sleeve=GND
@9
PGM1, 2 FADER output jacks
• Connect these jacks to the FADER input jacks of
DN-S3000, DN-S5000, DN-S1000 and etc. using
the 3.5mm stereo mini cord.
#0
Phono ground screw (GND)
• This screws provide a place to connect the
ground wire from a turntable.
• This terminal is exclusively for a turntable
ground and not a safety earth ground.
#1
PHONO1, 2 / LINE1, 3 switches
(LN / PH)
• These switches change the input from PHONO
to a LINE level input.
• These switches set a LINE level input when
turntable is not connected.
NOTE:
Always be sure main power is shut off before
change the position of the Line Level Selector
Switch.
#2
PHONO1, 2 / LINE1, 3 input jacks
• These stereo pairs of unbalanced RCA jacks are
inputs for a PHONO (RIAA) stage for magnetic
(MM) cartridges or a LINE stage suitable for any
device, such as a CD player.
#3
LINE2, 4 input jacks
• These stereo pairs of unbalanced RCA jacks are
inputs for any line level device.
#4
AUX INPUT jacks
• This stereo pair of RCA jacks provides an
unbalanced line level input with independent top
panel AUX INPUT control.
• This input is mixed after the Crossfader and
EFFECT LOOP.
#5
BOOTH OUT jacks
• This stereo pair of RCA jacks is the same as the
MASTER output with independent BOOTH
LEVEL control.
• This output may be for recording, booth/zone
monitoring, or for connecting to another mixer.
#6
UNBALANCED MASTER OUT jacks
• This stereo pair of RCA jacks provides an
unbalanced line level output.
• Connect these jacks to the unbalanced analog
input jacks on an amplifier or console.
#7
AC IN
• Input connection for the included AC adaptor.
NOTE:
Use specified attached AC adaptor only.
(3) Front panel
#8
CH 1/2 FADER START switches
• Use this to switch the Channel Fader Start
function ON and OFF.
#9
CROSSFADER START A, B switches
• Use this to switch the Crossader Start function
ON and OFF.
$0
HEADPHONE output jack
• Accept 1/4” stereo headphone plugs.
$1
CH 1/2 FADER CONTOUR
adjustment
• Adjusts the curve of the CH1/2 faders between
fast, normal , or slow fade.
$2
CH 1/2 FADER REVERSE switch
• Reverses the direction of each respective input
CH1/2 fader.
$3
CROSSFADER CONTOUR
adjustment
• Adjusts the shape of the crossfader curve from
a fast cut for scratching or to a slow fade for
mixing.
$4
CROSSFADER REVERSE switch
• Reverses the direction of the crossfader.
