Denon D-T1 Скачать руководство пользователя | Manualshive

Страница: 38 / 51

background image

TROUBLE SHOOTING

1. The unit will not power on (protection is activated)

The Power LED (red) is blinking.

D-AMP protection is activated.

44pin (AMP_FAULT) for [U10 : STM32F030] is

"Lo"

An abnormality has occurred in the output of D-

AMP, [U19 : STA339BW]

The DC detection circuit is activated.

([Q16, Q17] are on)

Check for open or short circuits in the circuits

connected to [6, 9, 10, 13pin] of the [U19 :

STA339BW] output.

If there are no abnormalities, there may be a

defect in [U19].

2. The unit will not power on (other

".

Check for abnormalities in the power supply.

SYS_3V3, SYS_5V, STB_3V3

An abnormal temperature increase has occurred

in D-AMP [U19], or overcurrent detection is

activated.

Check for open or short circuits in the circuits

connected to [6, 9, 10, 13pin] of the [U19:

STA339BW] output.

Check for abnormalities in the circuits around

[U19].

If there are no abnormalities, there may be a

defect in [U19].

NO

NO

NO

YES

YES

YES

Before Servicing

This Unit

Electrical

Mechanical

Repair Information

Updating

38

«
...
36
37
38
39
40
...
»

Содержание D-T1




















































Отзывы:

Нет отзывов

Похожие инструкции для D-T1

Бренд: R&S Страницы: 183

Бренд: AccessPRO Страницы: 8

Бренд: Yamaha Страницы: 99

Бренд: Yamaha Страницы: 74

V665 - RX AV Receiver

Бренд: Yamaha Страницы: 2

Бренд: Strong Страницы: 24

Бренд: Vauxhall Страницы: 137

AquaTronics MS250

Бренд: ASA Electronics Страницы: 5

Бренд: Trantec Страницы: 22

Бренд: Aiwa Страницы: 22

Бренд: Rockford Fosgate Страницы: 8

Бренд: Onkyo Страницы: 36

Бренд: PIE Страницы: 2

Бренд: CYP Страницы: 24

Бренд: Avanti Страницы: 24

7000 Monitor series

Бренд: NAD Страницы: 28

Бренд: Curtis Страницы: 1

Бренд: SecurityMan Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды