Denon D-T1 Скачать руководство пользователя

Страница: 39 / 51

Check of SYS_3.3V.

MAIN PCB

Voltage is supplied as normal to [Q3 : Drain].

Check of VCC12.

MAIN PCB

Voltage is supplied as normal to [U2 : 5pin].

Malfunction of DSP

MAIN PCB

[U5,U4]

Check the surrounding circuits.

Check the state / soldering for the following

parts.

MAIN PCB

Check the circuits around [Q3].

Check the state / soldering for the following

parts.

MAIN PCB

Check the circuits around [U2].

YES

2. The unit will not power on (other cause)

Check of POWER 14V.

SMPS PCB

Voltage is supplied as normal to [CON503 : 1,

2pin].

Check of STB_5V.

MAIN PCB

Voltage is supplied as normal to [FB27, FB28].

Check of STB_MCU_3.3V.

MAIN PCB

Voltage is supplied as normal to [L5].

Check of MCU Interface.

MAIN PCB

[U10 : 7pin] MCU=RST is "Hi".

[28pin] falls to "Lo" when the power button of

[U10 : 28pin] is pressed.

Check the operation of MCU.

MAIN PCB

POWER_EN changes from "Lo" to "Hi" when [U10

: 3pin] is powered on.

With [U10 : 58, 59pin] powered on, start com-

munication with [U5 : SPHE8104] using this port.

Check of STB_3.3V.

MAIN PCB

Voltage is supplied as normal to [U1].

Check the state / soldering for the following

parts.

SMPS PCB

Check the circuits around [F501, D553-D556,

U501, T501, U502, U503, U504, Q501].

Check the state / soldering for the following

parts.

MAIN PCB

Check the circuits around [U25].

Check the state / soldering for the following

parts.

MAIN PCB

Check the circuits around [U26].

Check for issues in the RESET circuit.

MAIN PCB

[R151, R152, D4, C141, C142]

Check for abnormalities in the power button and

its path.

DISPLAY PCB [SW7, ESD3]

Malfunction of MCU

MAIN PCB

[U10, U11]

Check the surrounding circuits.

Check the state / soldering for the following

parts.

MAIN PCB

Check the circuits around [U1].

YES

Before Servicing

This Unit

Electrical

Mechanical

Repair Information

Updating

Содержание D-T1



















































Результаты поиска

Содержание D-T1

Отзывы:

Похожие инструкции для D-T1

Бренды по названию

Популярные бренды

Denon D-T1, Руководство по обслуживанию

Результаты поиска

Содержание D-T1

Отзывы:

Похожие инструкции для D-T1

Бренды по названию

Популярные бренды