Denali MW1-SS Скачать руководство пользователя страница 4

Installing the filter Inside: Part 2

Page   of 

4

7

Bottleless,com.    xowater.com

© 2018 XO Water, LLC. All rights reserved.

Remove filter caps 

Push in on ring around the 
water inlet or outlet while 
you simultaneously pull the 
red cap(s) out. Pushing on 
the ring unlocks any 
waterway or caps so they 
can be removed.

Once waterway is 
pushed in, pull 
gently to test 

Pull on the waterway to 
check that it is secure. 

Write date on filter 

Write today's date on the 
front of the filter so you know 
when you installed/replaced 
the filter. Filters should be 
changed every 6 months and 
are available on our website 
or on amazon.com. 

Attach filter head to 
filter by pushing 
down, then rotating 

Push filter head down onto 
filter by rotating it around 
until it “fits”. Then, push all 
the way down and then 
rotate until it stops. 

Turn water on 

Place filter inside of bucket 
(next step) so that water will 
not get on floor. Turn water 
on by rotating valve so that 
it is parallel with waterway. 
The valve may be behind the 
cooler or at the sink.

Flush the filter 

Place bucket, trash can or 
co

ee pot under filter. 

Remember, water flows with 
arrow. Drain about 3 gallons 
of water to flush any carbon 
fines that can come loose 
during shipping.  

Turn water off 

To turn the water o

, turn the 

valve so that it is 
perpendicular to the 
waterway. 

Push waterway that 
goes to cooler into 
filter head 

Remove the black cap and 
push the waterway that 
goes TO cooler into head 
until it stops. Pull gently to 
make sure that it's secure. 

Push filter into 
bracket 

Push the filter into the 
middle filter bracket. 

Filter is secure in 
filter bracket 

This is what the filter will 
look like when it’s set up 
and inside of the Denali 
cooler. 

Turn water on 

You cooler will start to fill up. 

Insert waterway 
from water source 
into filter head  

On filter head, please note 
direction of arrow (shows 
direction of water flow TO 
cooler). Push the waterway 
into head until it stops. 

3 Gallons

In from 

water 

source

1) PUSH IN 

ON RING TO 

UNLOCK

Arrow 

goes this 

way

WATER VALVE IN 

OFF POSITION

ARROW GOES THIS WAY

WATER FROM 

SOURCE

WATERWAY TO 

COOLER

1

2

1

2

Содержание MW1-SS







Отзывы: