Delta Sidekick 36-210 Скачать руководство пользователя страница 4

4

ADDITIONAL SAFETY RULES

FOR COMPOUND MITER BOXES

1.

WARNING: USE ONLY CROSS-CUTTING SAW

BLADES. WHEN USING CARBIDE TIPPED BLADES,
MAKE SURE THEY HAVE A NEGATIVE HOOK ANGLE.
DO NOT USE BLADES WITH DEEP GULLETS AS
THEY CAN DEFLECT AND CONTACT GUARD.

2.

WARNING: Do not operate the miter box until it is

completely assembled and installed according to the
instructions.

3.

IF YOU ARE NOT thoroughly familiar with the oper-

ation of compound miter boxes, obtain advice from your
supervisor, instructor or other qualified person.

4.

DO NOT perform any operation freehand. Secure or

clamp workpiece firmly against fence.

5.

WARNING: Keep hands out of path of saw blade. If

the workpiece you are cutting would cause your hand to
be within 4 inches of the saw blade, the workpiece
should be clamped in place before making cut.

6.

BE SURE blade is sharp, runs freely and is free of

vibration.

7.

ALLOW the motor to come up to full speed before

starting cut.

8.

KEEP motor air slots clean and free of chips.

9.

ALWAYS MAKE SURE all clamp handles are tight

before cutting, even if the table is positioned in one of the
positive stops.

10. BE SURE blade and flanges are clean and that arbor
screw is tightened securely.

11. USE only blade flanges specified for your saw.

12. NEVER use blades larger or smaller in diameter than
ten inches.

13. NEVER apply lubricants to the blade when it is
running.

14. ALWAYS check the blade for cracks or damage
before operation. Replace cracked or damaged blade
immediately.

15. NEVER use blades recommended for operation at
less than 5500 RPM.

16. DO NOT operate the saw without guards in place.

17. ALWAYS keep the lower blade guard in place and
operating properly.

18. NEVER reach around or behind saw blade.

19. MAKE SURE blade is not contacting workpiece
before switch is turned on.

20. NEVER lock the switch in the “ON” position.

21. IMPORTANT: After completing cut, release power
switch and wait for coasting blade to stop before return-
ing saw to raised position.

22. TURN OFF tool and wait for saw blade to stop
before moving workpiece or changing settings.

23. DO NOT remove jammed or cut-off pieces until
blade has stopped.

24. NEVER cut ferrous metals or masonry.

25. NEVER recut small pieces.

26. PROVIDE adequate support to the sides of the saw
table for long workpieces.

27. NEVER use the miter box in an area with flammable
liquids or gases.

28. NEVER use solvents to clean plastic parts. Solvents
could possibly dissolve or otherwise damage the materi-
al. Only a soft damp cloth should be used to clean plas-
tic parts.

29. DISCONNECT power before changing blades or
servicing.

30. DISCONNECT saw from power source and clean
the machine before leaving it.

31. MAKE SURE the work area is cleaned before leav-
ing the machine.

32. THE USE of attachments and accessories not rec-
ommended by Delta may result in the risk of injuries.

33. SHOULD any part of your miter box be missing,
damaged or fail in any way, or any electrical component
fail to perform properly, shut off switch and remove plug
from power supply outlet. Replace missing, damaged or
failed parts before resuming operation.

34. ADDITIONAL INFORMATION regarding the safe
and proper operation of this product is available from the
National Safety Council, 1121 Spring Lake Drive, Itasca,
IL 60143-3201, in the Accident Prevention Manual for In-
dustrial Operation and also in the Safety Data Sheets
provided by the NSC. Please also refer to the American
National Standard Institute ANSI 01.1 Safety Require-
ments for Woodworking Machinery and the U.S. Depart-
ment of Labor OSHA 1910.213 Regulations.

35. SAVE THESE INSTRUCTIONS. Refer to them often
and use them to instruct others.

Содержание Sidekick 36-210





















Отзывы: