20201130
■ DRM (Digital input)
Function Port
Specifications
1. Click [On] to turn on the function.
2. Click [SET]
3. Follow below table to set the specific power limit value, you can check the percentage
by DRM(%) on the APP.
■ PARTIAL/ZERO EXPORT
The function has to be used with current sensor (optional part).
1. Click [On] to turn on the power meter function.
2. Click [On] to turn on the partial/zero export function.
3. Set the Rate% base on power company or local regulation.
4. Set the Sign capacity & PV capacity, the inverter will use the lower value as the power
limit reference, and then click [SET].
■ DRY CONTACT
1. The types of alert are “On grid, Insulation, Alarm, Error and Fault”, select to trigger.
2. Click [SET]
3. When the Inverter triggers the selected alarm, the inverter will close dry contact relay
to trigger external device.
Digital input
Power meter
Dry contact
* Screw torque required for
assembling: 8±2 kgf-cm
Short pins
Inverter behavior (AU)
D6 & D2
D6 & D1
D6 & D3
D6 & D4
D6 & D5
DRM 7 - Power de-rating to 75%
DRM 5 - Power de-rating to 0%
DRM 6 - Power de-rating to 50%
DRM 8 - Power de-rating to 100%
DRM 0 - Disconnect from grid
D1
D2
D3
D4
D5
D6
Dry
contact
Dry
contact
Power
meter
Power
meter
■ DRM (Digital input)
■ PARTIAL/ZERO EXPORT
■ DRY CONTACT
Enclosure
Operating temperature
Relative humidity
Galvanic isolation
Safety class
Overvoltage category
Flicker impedance
Three-phase combinations
Max. input voltage
Operating voltage range
MPP range (rated power)
Normal voltage
MPP tracker
Startup voltage
Input connection
Max. inverter backfeed
current to the array
Maximum input current
Max. short circuit current (per MPPT)
Operating Altitude
Environmental category
Pollution degree
Nominal output power
1
Maximum power
Nominal output current
Maximum output fault current
Maximum output over current protection
Frequency
Total harmonic distortion
2
Power factor
2
Peak efficiency
EU efficiency
Output connection
Voltage
Max. output current
Current (inrush)
(A, peak and duration)
Housing
Cooling
IP rating
External communication
Weight
Dimensions
GENERAL
DC INPUT (Solar side)
AC OUTPUT (Grid side)
MECHANISM
Powder-coated aluminium
-25~60°C, full power up to 40°C
2000 m
0% – 95% non-condensing.
Outdoor, wet locations
No (TL Topology)
Class I metal enclosure with protective earth
Internal: II, External: III
AC output: III, DC input: II
Z = 0.4 + j 0.25 Ω (total impedance)
No
600 Vdc
350 Vdc
30-550 Vdc
240-500 Vdc
11 Adc for each / 22 Adc for total
2
15 A
0 A
35 Vdc
H4, 2 pairs
230Vac -20%~+22%
30 A peak, 1 ms
50/60 Hz
<3% @Rated power
>0.99 @Rated power
97.5%
96.8%
IP 67 single-phase
5000 VA
5000 VA
25 A
25 A
22 A
23 A
Die casting
Convection cooling
IP65
Wi-Fi
12 kg
380 × 318 × 130 mm
1: (a) 4.99kVA max. for Australia (AU / NZ)
(b) 4.6kVA max. for Germany (DE)
2: reactive power control disabled
3: not support AS4777.2:2015 Single-phase inverters used in three-phase combinations
4: Information of regulations and directives please refer to user manual.
1. Follow the APP guideline to create an account and connect to the inverter.
Starting up the inverter function
5. Enter password (please contact us)
2. Click
3. Click “SETTING”
4. Click “Other”
2
1
1
1
1
3
4
2
4
2
2
❸
❹