background image

10- ENG

A04032

7.

Turn water source on.
NOTE: 

Failure to do so could

cause damage to the pump.

8.

Start engine.

See Engine Owners

Manual for correct procedure.

NOTE: 

When engine rope is

pulled, pressure starts building in
the gun. If the engine does not
start after two pulls, pull the gun
trigger to relieve this pressure.

9.

Depress trigger on gun to start
water flow. NOTE: Stand on a
stable surface

and grip

gun/spray wand firmly with both
hands. Expect the gun to kick
when triggered.

10. Release trigger to stop water

flow.

11. Adjust nozzle spray for the task

being performed. See How To Use
Wand instructions in this section.

SHUTTING DOWN

1.

After each use,

if you have

applied chemicals, place chemical
hose into container of clean water
and draw clean water through
chemical injection system to rinse
system thoroughly.

NOTE:

Failure

to do so could cause damage to
the pump.

2.

Turn engine off.

See Engine

Owner’s Manual. 

NOTE: NEVER

turn the water off with the engine
running.

3.

Turn water source off.

4.

Pull trigger on spray gun

to

relieve any water pressure in hose
or spray gun.

5.

See Storage section

in this

manual for proper storage
procedures.

STARTING

Prior to starting, refer to your engine
manual for proper starting
procedure.

1.

In a well ventilated outdoor area

add fresh, high quality, unleaded
gasoline with a pump octane
rating of 86 or higher.  Do not
overfill. Wipe up spilled fuel before
starting the engine. Refer to
Engine Owners Manual for correct
procedure.

2.

Check engine oil level.

See

Engine Owners Manual for correct
procedure. 

NOTE: There will be a

slight amount of oil in the
engine from factory testing.

3.

Verify the filter
screen

is in water

inlet of pump.

NOTE: 

Cone side

faces out.

4.

Connect

water

source to pump inlet.

NOTE:

Water source must provide a

minimum of 5 gallons per minute at
20 PSI.

5.

Connect

high pressure hose to

pump outlet.

6.

If applying a chemical or
cleaning solution

, see How To

Apply Chemicals/Cleaning
Solvents instructions in this
section.

High Pressure Hose

Water
Source

Filter Screen

Содержание DTT2450

















Отзывы: