Fig. D
Fig. E
Inch (mm)
A
B
16.125(409.6)
12.25(311.2)
Fig. F
DUCT CONNECTION
CONNECT WIRING
OFF
ON
L
N
POWER SWITCH
JUNCTION BOX
SWITCH BOX
WHITE
BLACK
GREEN
GRD
BLACK
ON/OFF SWITCH
(purchase separately)
SWITCH BOX
120 VAC
LINE IN
WHITE
GROUND
(bare)
POWER
SWITCH
WIRING
PLATE
GRILLE ATTACHMENT & TEST
RUN
1.
Insert the mounting springs into the slots and
mount the grille to the body. (Fig. H)
Slots
Fig. H
OPERATION
MAINTENANCE
WARNING:
DIMENSIONS
6
7 .7 5 "
12
.25
"
12.2
5"
15
"
15"
SPECIFICATIONS
Model No.
Voltage
(V)
Frequency
(Hz)
Power
@ 0.1SP
(W)
Air Flow
@ 0.1SP
(CFM)
Weight
(lb.)
Power
(W)
Pro200
120
60
17.5
200
12.6
30
Note: Design and specifications subject to change without notice.
WARRANTY
DELTA ELECTRONICS THREE YEAR LIMITED WARRANTY
Delta Electronics Inc. (‘‘Delta Electronics’’) warrants to the
original consumer purchaser in the USA that the Breez
ventilation fan products will be free from defects in material or
workmanship. This warranty is limited to three (3) years from
the original date of purchase.
Limitations and Exclusions
1. During the warranty period, a replacement for any defective
product will be supplied free of charge for installation by the
consumer. The warranty provided herein does not cover
charges for labor or other costs incurred in the
troubleshooting, repair, removal, and installation service.
2. All returns of defective parts or products must include the
product model number, and must be made through an
authorized Delta Electronics distributor. Authorized returns
must be shipped prepaid. Repaired or replacement products
will be shipped by Delta Electronics F.O.B. shipping point.
3. Delta Electronics shall not be liable for any indirect,
incidental, consequential, punitive, or special damages
arising out of or in connection with products use or
performance, regardless of the form of action whether in
contract, tort (including negligence), strict product liability
or otherwise.
4. This warranty does not extend to fluorescent lamp starters
and tubes.
5. The warranty does not cover if user does not comply with
manufacturer’s installation manual.
6. To qualify for warranty service, you must notify Delta
Electronics at the address or telephone number below.
7. Delta Electronics shall have no liability to the original
owner-user with respect to any defect caused by abuse,
misuse, neglect, improper transportation or storage,
improper testing, improper installation, improper operation,
improper use, improper maintenance, improper repair,
improper alteration, improper modification, tampering or
accident of products or parts thereof, or unusual
deterioration or degradation of products or parts thereof
due to a physical environment beyond the requirements of
products’ specifications.
Address: 46101 Fremont Blvd., Fremont, CA 94538
US Toll Free Number: 1-888-979-9889
Suspension bracket
Rubber
Screw
MODEL
Pro200
Ceiling
Body
Tape
Duct
Outside
Gradient
1
o
~ 2
o
Inside
Duct connector
Fig. G
Page 2.
Install the housing (I) - SUSPENDED CEILING
1.
Assemble suspension bracket and rubber to
body. (Fig. D)
Suspend body with anchor bolts. (Fig. E)
1. Follow all local electrical code and ANSI/NFPA70.
2.
NEVER place a switch where it can be reached
from a tub or shower.
3.
Connect wires as shown in wiring diagrams.
1. Insert the 6” duct (not provided) into the duct
connector and tape all ductwork connections
to make them secure and airtight. (Fig. G)
2. Install the duct with a gradient 1°~2° to the
outside.
1. Turn the POWER switch on to operate at single
speed mode - the LED indicator will be green.
4.
Using wire nuts (not provided), connect the
house power cable to the ventilating fan wires.
5.
14 AWG (2.1 mm2) is the smallest conductor
that shall be used for branch-circuit wiring.
Disconnect the power source before working on the
unit. Routine maintenance must be done every year.
CAUTION:
1. Never use gasoline, benzene, thinner or any other
such chemicals to clean the ventilating fan.
2. Do not allow water to enter the motor.
3. Do not soak resin parts in water over 140°F (60°C).
CLEANING
1. Pull down the springs to remove the grille.
2. Wash and clean the grille. (Use non-abrasive kitchen
detergent and wipe dry with a new cloth.)
3. Using a cloth dampened with non-abrasive kitchen
detergent, remove any dirt from the ventilating fan.
Wipe dry with a new cloth.
4. Replace the grille.
Install the housing (II) - WOODEN HEADER
1. Install header between ceiling joists using
nails or screws.
2.
Install the ventilating fan to the header with
long screws (Ø 4x25). (Fig. F)
