2
ADDITIONAL SAFETY RULES FOR
AIR CLEANERS
1.
DO NOT USE THIS UNIT TO FILTER METAL DUST.
Combining wood and metal dust can cre-
ate an explosion or fire hazard. This unit is intended to filter non-explosive atmospheres only.
2 .
WARNING: DUST GENERATED BY CERTAIN WOODS AND WOOD PRODUCTS CAN BE HAZ-
ARDOUS TO YOUR HEALTH.
3.
DO NOT USE THIS UNIT TO DISSIPATE FUMES OR SMOKE
.
This air cleaner is intended for use
where only dry airborne dust is present. Its use should be limited to non-explosive, non-metallic atmospheres.
4
. DO NOT OPERATE THIS UNIT UNTIL IT IS COMPLETELY ASSEMBLED AND INSTALLED ACCORDING TO
THE INSTRUCTIONS
.
5.
OBTAIN ADVICE FROM YOUR SUPERVISOR, INSTRUCTOR, OR ANOTHER QUALIFIED PERSON
if you are
not thoroughly familiar with the operation of this unit.
6.
FOLLOW ALL WIRING CODES
and recommended electrical connections.
7.
DO NOT LIFT THIS UNIT BY THE POWER CORD.
Do not use the power cord as a hanging device.
8.
SECURELY ANCHOR THIS UNIT INTO A SUPPORTING STRUCTURE
when suspending it from the ceiling.
Always keep a minimum of 7 feet between the bottom of the unit and the floor surface to allow for sufficient head
clearance. Use only chain rated for a minimum of 150 lb. working load to adequately hold the unit. Use steel S-
Hooks that are at least 1/4" in diameter to suspend the unit from the ceiling. Lag-type bolts used to suspend the
unit from the ceiling must be threaded at least 1-1/2" into supporting structural members.
9.
SUPPORT THIS UNIT OR SECURELY CLAMP IT TO THE WORK SURFACE WHEN IT IS USED IN A
PORTABLE APPLICATION
to eliminate potential movement and/or damage from falling.
10.
INSURE THAT THE INTAKE AND EXHAUST AREAS ARE CLEAR PRIOR TO STARTING THE UNIT.
11.
KEEP ARMS, HANDS, AND FINGERS AWAY FROM THE FAN.
Avoid all exposure to rotating parts.
12.
DO NOT OPERATE THIS UNIT WITHOUT THE FILTERS IN PLACE.
GENERAL SAFETY RULES
Woodworking can be dangerous if safe and proper operating procedures are not followed. As with all machinery,
there are certain hazards involved with the operation of the product. Using the machine with respect and caution
will considerably lessen the possibility of personal injury. However, if normal safety precautions are overlooked or
ignored, personal injury to the operator may result. Safety equipment such as guards, push sticks, hold-downs,
featherboards, goggles, dust masks and hearing protection can reduce your potential for injury. But even the best
guard won’t make up for poor judgment, carelessness or inattention. Always use common sense and exercise
caution in the workshop. If a procedure feels dangerous, don’t try it. Figure out an alternative procedure that feels
safer.
REMEMBER:
Your personal safety is your responsibility.
This machine was designed for certain applications only. Delta Machinery strongly recommends that this machine
not be modified and/or used for any application other than that for which it was designed. If you have any ques-
tions relative to a particular application,
DO NOT
use the machine until you have first contacted Delta to deter-
mine if it can or should be performed on the product.
Technical Service Manager
Delta Machinery
4825 Highway 45 North
Jackson, TN 38305
(IN CANADA: 505 SOUTHGATE DRIVE, GUELPH, ONTARIO N1H 6M7)
FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY.
1.
FOR YOUR OWN SAFETY, READ AND UNDERSTAND THE INSTRUCTION MANUAL BEFORE OPERATING THE
UNIT
. Learn the unit’s application and limitations as well as the specific hazards peculiar to it.
2.
KEEP WORK AREA CLEAN
. Cluttered areas and benches invite accidents.
3.
DON’T USE IN DANGEROUS ENVIRONMENT.
Don’t use this unit in damp or wet locations, or expose it to rain. Keep
work area well-lighted.
4.
KEEP CHILDREN AND VISITORS AWAY
. All children and visitors should be kept a safe distance from work area.
5.
DISCONNECT UNIT
before servicing.
6.
CHECK DAMAGED PARTS
. Before further use of the unit, properly repair or replace any part that is damaged.
