background image

Delta will repair or replace, at its expense and at its option, any Delta machine, machine part, or
machine accessory which in normal use has proven to be defective in workmanship or material,
provided that the customer returns the product prepaid to a Delta factory service center or author-
ized service station with proof of purchase of the product within two years and provides Delta with
reasonable opportunity to verify the alleged defect by inspection. Delta may require that electric
motors be returned prepaid to a motor manufacturer s authorized station for inspection and repair
or replacement. Delta will not be responsible for any asserted defect which has resulted from nor-
mal wear, misuse, abuse or repair or alteration made or specifically authorized by anyone other
than an authorized Delta Service facility or representative. Under no circumstances will Delta be
liable for incidental or consequential damages resulting from defective products. This warranty is
Delta s sole warranty and sets forth the customer s exclusive remedy, with respect to defective
products; all other warranties, express or implied, whether of merchantability, fitness for purpose,
or otherwise, are expressly disclaimed by Delta.

Delta Building Trades and Home Shop Machinery

Two Year Limited Warranty

22

Printed in U.S.A.

Содержание 37-285
























Отзывы: