Delta 36-729 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 28

Delta 36-729 Скачать руководство пользователя страница 18

18

MITER GAGE OPERATION AND
ADJUSTMENT

The miter gage is equipped with adjustable index stops
at 90 degrees and 45 degrees right and left. Adjustment
to the index stops can be made by tightening or
loosening the three adjusting screws (B) Fig. 40, with
allen wrench supplied.

To rotate the miter gage, loosen lock knob (A) Fig. 40, flip
the stop link (D) down and out of the way, and move the
body of the miter gage (C), to the desired angle.

The miter gage body (C) can stop at 90 degrees and 45
degrees both right and left by flipping the stop link down
and out of the way and moving the miter gage body (C)
past the 90 and 45 degrees mark and flipping the stop
link (D) back up so that the stop link (D) will be able to
contact the adjusting screws (B) at the desired 90 or 45
degree angle. To rotate the miter gage body past these
points, the stop link (D) Fig. 40, must be down and out of
the way.

Your miter gage is equipped with a plate which fits into
the T-Slot groove in the table. This allows the miter gage
to be pulled off the front edge of the table without falling.
This allows for a longer cut off capacity in front of the
blade.

Fig. 40

B

B

B

A

D

C

«
...
16
17
18
19
20
...
»

Содержание 36-729





























Отзывы:

Нет отзывов