Delta 31-750 Скачать руководство пользователя страница 9

9

C O N N E C T I N G S A N D E R TO P O W E R S O U R C E

P O W E R C O N N E C T I O N S

A separate electrical circuit should be used for your tools. This circuit should not be less

than #12 wire and should be protected with a 20 Amp fuse. Have a certified electrician

replace or repair a worn cord immediately. Before connecting the motor to a power line,

make sure the switch is in the  OFF  position and be sure that the electric current is of

the same characteristics as stamped on the motor nameplate. Running on low voltage

will damage the motor.

W ARNING: DO NOT EXPOSE THE TO O L TO RAIN OR OPERATE THE TO O L IN

D A M P L O C ATIONS.

M O TOR SPECIFICATIONS

Your sander is wired for 110-120 volt, 60 Hz alternating current. Before connecting the

sander to the power source, make sure the switch is in the  OFF  position. The 3600

RPM motor provides 3600 oscillations per minute.

FASTENING S A N D E R TO A SUPPORTING S U R FA C E

If during operation there is any tendency for the sander to tip over, slide or walk, the

sander must be secured to the supporting surface using the four holes in the base of

the machine. If you purchased the accessory stand, the four plastic feet supplied with

the stand feature holes which allow easy mounting of the stand to a supporting surface.

Fig. 17

A C C E S S O RY 31-752 DISC H O L D E R

An accessory abrasive disc holder (A) Fig. 16, is available to conveniently store extra

abrasive discs. The disc holder (A) slides neatly into the pocket of the sander as shown

in Fig. 17.

Fig. 16

A

A

Содержание 31-750













Отзывы: