Delta 28-190 Скачать руководство пользователя страница 18

18

Delta Building Trades and Home Shop Machinery

Two Year Limited Warranty

Delta will repair or replace, at its expense and at its option, any Delta machine,
machine part, or machine accessory which in normal use has proven to be
defective in workmanship or material, provided that the customer returns the
product prepaid to a Delta factory service center or authorized service station with
proof of purchase of the product within two years and provides Delta with
reasonable opportunity to verify the alleged defect by inspection. Delta may require
that electric motors be returned prepaid to a motor manufacturer’s authorized
station for inspection and repair or replacement. Delta will not be responsible for
any asserted defect which has resulted from normal wear, misuse, abuse or repair
or alteration made or specifically authorized by anyone other than an authorized
Delta service facility or representative. Under no circumstances will Delta be liable
for incidental or consequential damages resulting from defective products. This
warranty is Delta’s sole warranty and sets forth the customer’s exclusive remedy,
with respect to defective products; all other warranties, express or implied,
whether of merchantability, fitness for purpose, or otherwise, are expressly
disclaimed by Delta.

Printed in U.S.A.

Содержание 28-190



















Отзывы: