background image

7

Fig. D-1

MINIMUM GAUGE EXTENSION CORD

RECOMMENDED SIZES FOR USE WITH STATIONARY ELECTRIC MACHINES

Ampere

Total Length

Gauge of

Rating

Volts

of Cord in Feet

Extension Cord

0-6

120

up to 25

18 AWG

0-6

120

25-50

16 AWG

0-6

120

50-100

16 AWG

0-6

120

100-150

14 AWG

6-10

120

up to 25

18 AWG

6-10

120

25-50

16 AWG

6-10

120

50-100

14 AWG

6-10

120

100-150

12 AWG      

10-12

120

up to 25

16 AWG

10-12

120

25-50

16 AWG

10-12

120

50-100

14 AWG

10-12

120

100-150

12 AWG

12-16

120

up to 25

14 AWG

12-16

120

25-50

12 AWG

12-16

120

GREATER THAN 50 FEET NOT RECOMMENDED

EXTENSION CORDS

Use proper extension cords. Make sure

your extension cord is in good condition and is a 3-wire
extension cord which has a 3-prong grounding type plug
and matching receptacle which will accept the
machine’s plug. When using an extension cord, be sure
to use one heavy enough to carry the current of the
machine. An undersized cord will cause a drop in line
voltage, resulting in loss of power and overheating. Fig.
D-1 or D-2, shows the correct gauge to use depending
on the cord length. If in doubt, use the next heavier
gauge. The smaller the gauge number, the heavier the
cord.     

FOREWORD

FUNCTIONAL DESCRIPTION

The Delta Industrial 23-725 8” Slow-Speed Grinder includes a 3/4 HP motor wired at 120 volts, a flexible lamp, spark
guards, eyeshields, tool rests, wheel dresser, two wheels, a wrench and a water tray. Slow speed (1725 RPM) reduces
heat generated by grinding.

NOTICE: 

The photo on the manual cover illustarates the current production model. All other illustrations contained in

the manual are representative only and may not depict the actual labeling or accessories included. These are are
intended to illustrate technique only.

Содержание 23-725





















Отзывы: