manualshive.com logo in svg

Delta 20-142C, Инструкция по эксплуатации

Поделиться
Скачать
Delta 20-142C Скачать руководство пользователя страница 11

11

Figure 18

Rotate the front wheel guard (A) to the up
position.

Figure 19

Press arbor lock (A) toward wheel housing while
rotating wheel (B) by hand until the arbor lock
engages.

Figure 20

Using the supplied wrench, loosen arbor screw
(A) by turning it counterclockwise. Remove
arbor screw, washer (B), outside wheel flange
(C), and wheel (D).
NOTE: Do not remove inside wheel flange.
Clean the inside surfaces of both the inside and
outside wheel flanges.
Install new wheel and replace outside wheel
flange, washer, and arbor screw. Tighten arbor
screw clockwise.
IMPORTANT: Use only reinforced abrasive
wheels with blotters and tighten arbor screw
only enough to hold wheel firmly and prevent
slippage. Excessive tightening may result in
damage.
Rotate front wheel guard to down position and
disengage spindle lock before starting tool.

Fig. 18

Fig. 19

Fig. 20

MAINTENANCE

Changing The Abrasive Wheel

DISCONNECT TOOL FROM POWER SOURCE

Содержание 20-142C













Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды