Delta Tau PMAC2-PC/104 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 74

background image

PMAC2A-PC/104

Introduction

4

ACC-2P Option 3: I/O ports

Option 3 provides the following ports on the ACC-2P communications board for digital I/O connections.

•

Multiplexer Port: this connector provides eight input lines and eight output lines at TTL levels.
When using the PMAC ACC-34x type boards these lines allow multiplexing large numbers of
inputs and outputs on the port. Up to 32 of the multiplexed I/O boards may be daisy-chained on
the port, in any combination.

•

I/O Port: this port provides eight general-purpose digital inputs and eight general-purpose digital
outputs at 5 to 24 VDC levels. This 34-pin connector was designed for easy interface to OPTO-
22 or equivalent optically isolated I/O modules when different voltage levels or opto-isolation to
the PMAC2A-PC/104 is necessary.

•

Handwheel port: this port provides 2 extra channels, each jumper selectable between encoder
input or pulse output.

ACC-8TS connections board

ACC-8TS is a stack interface board to for the connection of either one or two ACC-28B A/D converter
boards. When a digital amplifier with current feedback is used the analog inputs provided by the ACC-
28B cannot be used.

ACC-8ES Four channel dual-DAC analog stack board

ACC-8ES provides four channels of 18-bit dual-DAC with four DB-9 connectors. This accessory stack
to the PMAC2A-PC/104 board and it is mostly used with amplifiers that require two ±10 V command
signals for sinusoidal commutation.

ACC-8FS Four channel direct PWM stack breakout board

ACC-8FS it is a 4-channel direct PWM stack breakout board for PMAC2A-PC/104. This is used for
controlling digital amplifiers that require direct PWM control signals. When a digital amplifier with
current feedback is used the analog inputs provided by the Opt-12 of the PMAC2A-PC/104, the Opt-2 of
the ACC-1P or the ACC-28B could not be used.

«
...
9
10
11
12
13
...
»

Содержание PMAC2-PC/104











































































Отзывы:

Нет отзывов

Похожие инструкции для PMAC2-PC/104

Бренд: IEI Technology Страницы: 19

Бренд: IEI Technology Страницы: 87

Бренд: IEI Technology Страницы: 3

Бренд: Edge-Core Страницы: 7

Бренд: Intel Страницы: 108

Бренд: Black Box Страницы: 9

Бренд: Delta Страницы: 2

Бренд: Ruckus Wireless Страницы: 102

Avenue Express Control Panel

Бренд: Ensemble Designs Страницы: 19

Converter Board R0E5212BACFG00

Бренд: Renesas Страницы: 6

Бренд: ZALMAN Страницы: 11

Бренд: H3C Страницы: 9

SteelCentral AppResponse 2180

Бренд: Riverbed Страницы: 82

Бренд: ZALMAN Страницы: 8

Бренд: Magma Страницы: 2

Бренд: Cypress Semiconductor Страницы: 15

Бренд: Digi Страницы: 75

Ultra WiFi Booster

Бренд: Optus Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды