Delta Tau ACC-72EX Скачать руководство пользователя страница 111 | Manualshive

Страница: 111 / 146

background image

ACC-72EX User Manual

Diagnostics

111

EtherNet/IP

– Scanner/Master – OPT70

The following table describes the meaning of the LEDs for the comX Real-Time Ethernet communication
modules (COMX-CA-RE/ COMX-CNRE) when the firmware of the EtherNet/IP Scanner (Master)
protocol is loaded to the comX communication module:

MS LED (COM0)

Color

State

Meaning

Green

On

Device operational: If the device is operating correctly, the module status
indicator shall be steady green.

Green

Flashing

Standby: If the device has not been configured, the module status indicator
shall be flashing green.

Red

On

Major fault: If the device has detected a non-recoverable major fault, the
module status indicator shall be steady red.

Green

Flashing

Minor fault: If the device has detected a recoverable minor fault, the module
status indicator shall be flashing red. NOTE: An incorrect or inconsistent
configuration would be considered a minor fault.

Red/Green

Flashing

Self-test: While the device is performing its power up testing, the module status
indicator shall be flashing green/red.

-

Off

No power: If no power is supplied to the device, the module status indicator
shall be steady off.

NS LED (COM1)

Color

State

Meaning

Green

On

Connected: If the device has at least one established connection (even to the
Message Router), the network status indicator shall be steady green.

Green

Flashing

No connections: If the device has no established connections, but has obtained
an IP address, the network status indicator shall be flashing green.

Red

On

Duplicate IP: If the device has detected that its IP address is already in use, the
network status indicator shall be steady red.

Red

Flashing

Connection timeout: If one or more of the connections in which this device is
the target has timed out, the network status indicator shall be flashing red. This
shall be left only if all timed out connections are reestablished or if the device is
reset.

Red/Green

Flashing

Self-test: While the device is performing its power up testing, the network
status indicator shall be flashing green/red.

-

Off

Not powered, no IP address: If the device does not have an IP address (or is
powered off), the network status indicator shall be steady off.

LINK LED

Green LED on ETH0 / ETH1 connectors:

Color

State

Meaning

Green

On

A connection to the Ethernet exists

Green

Off

The device has no connection to the Ethernet

ACT LED

Yellow LED on ETH0 / ETH1 connectors:

Color

State

Meaning

Yellow

Flashing

The device sends/receives Ethernet frames

«
...
109
110
111
112
113
...
»

Содержание ACC-72EX



















































































































































Отзывы:

Нет отзывов

Похожие инструкции для ACC-72EX

Бренд: Paradyne Страницы: 20

Compshere 3000 Series

Бренд: Paradyne Страницы: 2

Бренд: Pantech Страницы: 17

SLK-R602 Series

Бренд: Seriallink Страницы: 29

Бренд: TP-Link Страницы: 2

Бренд: Hamlet Страницы: 11

Бренд: Enterasys Страницы: 62

Cheetah EtherCard-2320

Бренд: Accton Technology Страницы: 10

Бренд: C&H Technologies Страницы: 2

Passport 8608GTE

Бренд: Nortel Страницы: 10

Бренд: Allied Telesis Страницы: 128

Бренд: ZyXEL Communications Страницы: 4

Бренд: Hamlet Страницы: 6

Бренд: Airaya Страницы: 28

Бренд: Korenix Страницы: 3

Бренд: D-Link Страницы: 2

Бренд: Billion Страницы: 20

Бренд: Johnson Controls Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды